Yes, the chain cases are light on this machine. 3/16" at most, and hard. When you drag it through mud right up to it's belly pan, daily, for months on end, the chains cases will wear. So does the belly pan. This one wore through in an area where there was no chain contact. I don't think the problem would be any different with a Thomas, Cat, Gehl, Case, Bobcat etc if they were doing the same job... IF they could do the job. Likewise, the mud does the wheel bearings in if I don't grease them often enough... which generally doesn't happen because I've got to pull the wheels to grease them. So it doesn't always happen on time. The motor shafts were changed because the bolts that retain the 'pinion shaft' to the motor shaft had their retainer/clamp bolts back out. I don't know why they backed out. Mabey they were never torqued right. I know I've got far more hours on it since with no trouble than I got before the rebuilds. It's just that the bolt fell out and the tapered spline got torn up before I took much notice of it. So... when I got rooting around in the chain case to repair that I put new chains in anyway. The only other problems I've had were hoses. I'm after changing most of them, but that's hardly the machines fault...
I still don't see why you need to 'see' the cutting edge. I've done plenty of work in ditches and road work with this machine where I was setting grades. You just get used to not seeing the edge and develop a feel for where it is.
I've spent time in a Thomas about the same size as this one... I think a 173. You can't see a thing behind you. You can't see much beside you... and you never know what way the damn thing will tip when you have the loader in the air. You just know it's going to tip... I had that one rented for a couple days before I bought this machine. I've used a Gehl... 6635 or something like that. It's a fair bit larger machine than mine. It seemed good but I don't like the pilot controls very much and it's still got poor visibility. I've played with a Case 75XT. That's a solid powerfull machine.... much larger than the LS170 and no more able to lift anything because it can't keep it's wheels on the ground. It'd need a huge counterweight to be usefull... and then need to be loaded all the time or it's pop wheelies. Last but not least... there is Cat. The biggest waste of space the skid steer market has ever seen. I didn't run one but I had to rescue one that a neighbour rented last summer. I went into the bog that he got stuck in and dragged him out with my 170... NH superboom loaders work better because they're better balanced and lighter. The low center of gravity keeps them stable while lifting and keeps their wheels planted while driving up hills. With very few exceptions, if they're going to tip, it will be forward, and it will be at maximum lift without counterweight. tipping ahead is not a big deal if you're quick enough to drop the loader. Tipping backwards can be fatal... Mabey that's why all the others need heavy armour on their backsides. Gives em something to roll onto...
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]
Today's Featured Article - Talk of the Town: The Saga of Grandpa's Tractor - by The following saga is from the Tractor Talk Discussion Forum. Someone. The saga starts with the following message: Hey guys I have a decision to make. I know what you all will probably suggest and it will probably agree with me way down inside, but here it is. I have a picture blown up and framed in my "tractor room" of a Farmall M. It was my Grandpa's tractor, of which whom I never got to meet. He froze to death getting this tractor out of the barn to pull a truck out of the ditch before I was born. Anyway my dad and aunt had to sell it at the auction,
... [Read Article]
Latest Ad:
Sell 1958 Hi-Altitude Massey Fergerson tractor, original condition. three point hitch pto engine, Runs well, photos available upon request
[More Ads]
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy
TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
