Posted by jdemaris on November 14, 2009 at 06:47:21 from (67.142.130.38):
In Reply to: HDTV Antenna posted by PopinJohn on November 13, 2009 at 17:39:25:
Just use the meter in your TV or converter box. They all have meters that give a reading that is a mix of signal strength and signal quality. An ohm-meter won't tell you a thing.
Remember that you can't just rotate the antenna to look for signals. You have to rotate a few degrees and then do a channel scan. Then rotate a few more and rescan, over and over. The TV will only work on those it has found, locked-into, and put into memory.
There is NO such thing as an HD antenna. But, you must have the correct one. Many TV stations changed bands during the change. So, some that were on VHF went over to UHF, and vice-versa. 14 - 51 UHF are the most common now, but several are using VHF 2-13 still.
If you have a VHF antenna, you won't get the many that changed to UHF. And, the converse.
Also, many stations move to different transmitter towers that may be a lot further away from you now.
Also keep in mind that with digital - there are now two channel numbers for each. "Virtual" and "actual" and that can get pretty confusing. Your TV will usually only show you the "virtual" channel. If you want to improve reception, you have to know what the actual channel is.
This was done so old-time TV stations could keep their original names.
For example - in my area of NY - Channel 12 is actually on VHF channel 7 now. Channel 13 is actually on VHF channel 12 now. Channel 10 is actually on UHF channel 26 now. Channel 2 is actually on UHF channel 29 now. Channel 40 (Fox 40)is actually on VHF channel 8 now.
Also, about coax, since somebody mentioned it. For your type of TV, RG59, RG6, or RG11 is used. RG59 is the cheapest and fine up to around 50 feet. RG6 cost a little more an pretty good up to around 200 feet. RG11 is the most expensive and can be used up to 300 feet before line-amps are needed.
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]
Today's Featured Article - Engine Valves - Some Helpful Information - by Staff. Intake - On the intake stroke the piston moves doward, sucking in carburized fuel through the open intake valve. Exhaust valve is closed. Compression - With both the intake and exhaust valves closed, the pistons upward stroke compresses or squeezes the fuel into the combustion chamber. Firing - Ignited by the spark, the compressed fuel explodes and forces the piston downward on its power stroke. Intake and exhaust valves are closed. Exhaust valves and seats are exp
... [Read Article]
Latest Ad:
Oliver 550 Diesel runs like a watch three point hitch pto engine gone threw about two hundred hours ago nice clean tractor
[More Ads]
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy
TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
