Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 
Marketplace
Classified Ads
Photo Ads
Tractor Parts
Salvage

Community
Discussion Forums
Project Journals
Your Stories
Events Calendar
Hauling Schedule

Galleries
Tractor Photos
Implement Photos
Vintage Photos
Help Identify
Parts & Pieces
Stuck & Troubled
Vintage Ads
Community Album
Photo Ad Archives

Research & Info
Articles
Tractor Registry
Tip of the Day
Safety Cartoons
Tractor Values
Serial Numbers
Tune-Up Guide
Paint Codes
List Prices
Production Nbrs
Tune-Up Specs
Torque Values
3-Point Specs
Glossary

Miscellaneous
Tractor Games
Just For Kids
Virtual Show
Museum Guide
Memorial Page
Feedback Form

Yesterday's Tractors Facebook Page

  
Tractor Talk Discussion Board

Re: Stuck and stripped oil plug...


[ View Follow Ups ] [ Post Followup ] [ Return to Forum ]

Posted by Bill on October 09, 2000 at 06:04:20 from (204.60.171.10):

In Reply to: Stuck and stripped oil plug... posted by Karl Bader on October 07, 2000 at 08:01:27:

Karl:

You helped me with a question posted on this board a while back, hope I can return the favor.

I thank Clooney (a frequent poster with help on this site) for this suggestion.

I just went through this 3 weeks ago on my JD Model AW (1949) and I hope your B has the same configuration -- regards oil plug.

Went to drain oil looked at plug and there was no nice square nut on top of plug -- just a rounded mass of metal. Tried "screw removers "(little and Big)--only managed to put large hole in center of plug (oil did not come out even with a half-inch hole through plug until I pulled out about a half gallon of goop that was the consistence of "Silly Putty"but that's another story).

After oil drains, and hole big enough clean through the oil plug, take a hacksaw blade and and make (top to bottom) cuts around the circumfrence of the plug(sort of like oblong pie slices) . ONLY CUT THROUGH UNTIL YOU CONTACT THE THREADS -- NOT THROUGH THREADS.

Then take a very small chisel (I found a 3/8 ths incher at True Value Hardware store) and CAREFULLY work at or near the cuts in the old oil plug until one of the sections comes out. The rest will come out a lot easier.

It took me about 3 hours total, but it did come out and the replacement plug went in normally and DID NOT LEAK.

I hope this helps. If you would like to talk about this procedure, send me your telephone number and I will call.

P.S. my plug was not stripped but was it was "gorilla-ed" in way past flush and would not budge with biggest vice-grips and 2-foot pipe lever.
Bill


Follow Ups:




Post A Followup

:
:

: Re: Re: Stuck and stripped oil plug...

:

:

:

:

: If you check this box, email will be sent to you whenever someone replies to this message. Your email address must be entered above to receive notification. This notification will be cancelled automatically after 2 weeks.


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Today's Featured Article - Third Brush Generators - by Chris Pratt. While I love straightening sheet metal, cleaning, and painting old tractors, I use every excuse to avoid working on the on the electrics. I find the whole process sheer mystery. I have picked up and attempted to read every auto and farm electrics book with no improvement in the situation. They all seem to start with a chapter entitled "Theory of Electricity". After a few paragraphs I usually close the book and go back to banging out dents. A good friend and I were recently discussing our tractor electrical systems when he stated "I figure it all comes back to applying Ohms Law". At this point ... [Read Article]

Latest Ad: John Deere B 1943 [More Ads]

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy