Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 
Marketplace
Classified Ads
Photo Ads
Tractor Parts
Salvage

Community
Discussion Forums
Project Journals
Your Stories
Events Calendar
Hauling Schedule

Galleries
Tractor Photos
Implement Photos
Vintage Photos
Help Identify
Parts & Pieces
Stuck & Troubled
Vintage Ads
Community Album
Photo Ad Archives

Research & Info
Articles
Tractor Registry
Tip of the Day
Safety Cartoons
Tractor Values
Serial Numbers
Tune-Up Guide
Paint Codes
List Prices
Production Nbrs
Tune-Up Specs
Torque Values
3-Point Specs
Glossary

Miscellaneous
Tractor Games
Just For Kids
Virtual Show
Museum Guide
Memorial Page
Feedback Form

Yesterday's Tractors Facebook Page

  

Re: Charging AC ?


[ Expand ] [ View Replies ] [ Add a Reply ] [ Return to Forum ]

Posted by 440roadrunner on June 04, 2009 at 18:03:23 from (98.145.76.31):

In Reply to: Charging AC ? posted by dr sportster on June 04, 2009 at 15:15:33:

One way to speed up charging an EMPTY system---we assume you have the system evacuated down--is to dump some liquid into the HIGH side before you start the system. The way you do this is as follows:

The service valves have "three" positions.

Normal "stem out" closes the test port, and opens the valve to feed the compressor head to the hot gas tube

"in the middle" leaves above operation intact, and opens the test port.

"Stem down" would be if you are swapping a compressor--closes off the head from the line so you can yank the compressor.

So you have the service valve "in the middle"--test port open, you have your manifold hooked up, and you are done evacuating and testing, the system is MT and under a vacuum.

You simply close the manifold, hookup and purge the refrigerant can, and turn it upside down, (purge the middle hose at gauge set)

Now you can just open the high side valve on the manifold set and dump liquid in the high end. It won't go back into the compressor, but will fill the condenser/ receiver and start to pressure through the TXV to the low side, and you will see the low side gauge start to rise.

This becomes a matter of practice, unless you are measuring a charge, with scales or whatever.

Turn the can upright to purge the liquid, and close the high side manifold valve

Fire the system and adjust the final charge. I ALWAYS check the suction line superheat for some idea as to condition in the line. Be sure to insulate your thermometer/ thermocouple well


Replies:




Add a Reply

:
:
: :

:

:

:

:

:

: If you check this box, email will be sent to you whenever someone replies to this message. Your email address must be entered above to receive notification. This notification will be cancelled automatically after 2 weeks.


 
Advanced Posting Tools
  Upload Photo  Select Gallery Photo  Attach Serial # List 
Return to Post 

TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Today's Featured Article - The Niagra View Mobile - Powered by a 1959 Ford Tractor - by Mark Massey. In 1959 the Niagara Frontier Transit Inc. of Buffalo, New York designed and built six Viewmobiles for the Niagara Frontier Sightseeing Inc. for use as a sightseeing ride at the Niagara Falls State Park, Niagara Falls, New York, powered by a 1959 Ford 611 Tractor. ... [Read Article]

Latest Ad: Oliver 550 Diesel runs like a watch three point hitch pto engine gone threw about two hundred hours ago nice clean tractor [More Ads]

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy