Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 
Marketplace
Classified Ads
Photo Ads
Tractor Parts
Salvage

Community
Discussion Forums
Project Journals
Your Stories
Events Calendar
Hauling Schedule

Galleries
Tractor Photos
Implement Photos
Vintage Photos
Help Identify
Parts & Pieces
Stuck & Troubled
Vintage Ads
Community Album
Photo Ad Archives

Research & Info
Articles
Tractor Registry
Tip of the Day
Safety Cartoons
Tractor Values
Serial Numbers
Tune-Up Guide
Paint Codes
List Prices
Production Nbrs
Tune-Up Specs
Torque Values
3-Point Specs
Glossary

Miscellaneous
Tractor Games
Just For Kids
Virtual Show
Museum Guide
Memorial Page
Feedback Form

Yesterday's Tractors Facebook Page

  
Tractor Talk Discussion Board

Re: I need a wiring diagram or description !!!


[ View Follow Ups ] [ Post Followup ] [ Return to Forum ]

Posted by Bob M on July 19, 2000 at 08:06:45 from (192.232.120.194):

In Reply to: I need a wiring diagram or description !!! posted by Alberta Mike on July 18, 2000 at 05:42:45:

third party image

Mike - Most tractors of that era were wired up pretty much the same. This diagram is a typical Delco set-up (used on a majority of 6 volt tractors). Chances are your Avery was wired close to this - it should at least help you get started. Possible changes:

1 - This diagram has the heavy manual pushbutton start switch mounted directly on the starter. If you have a separate remote switch, then run one cable from the battery "-" terminal to the switch, and a second cable from the switch to the starter terminal.

2 - Look for identification on the regulator terminals. One should be marked GEN, ARM or A. It gets connected to the ARM or A terminal on the generator. Another should be marked FLD or F. It goes to the FLD or F terminal on the generator. Next one should be marked BAT or B. It goes to the "-" connection on ammeter. Finally, if the regulator has only these 3 terminals, the wire going to L on the diagram should instead be connected to "-" terminal on the ammeter. Make sure the regulator base is fastened to a good ground too!

For recommended wire/cable sizes, see the legend on the diagram. (Note - it's OK to use #10 everywhere - except of course for battery cables).

Good luck!

Bob M


Follow Ups:




Post A Followup

:
:

: Re: Re: I need a wiring diagram or description !!!

:

:

:

:

: If you check this box, email will be sent to you whenever someone replies to this message. Your email address must be entered above to receive notification. This notification will be cancelled automatically after 2 weeks.


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Today's Featured Article - Women and Tractors - More Views From the Farmer's Wife - by Teri Burkholder. The top ten reasons why the judges wouldn't let you participate in the stock antique tractor pull: Hey, this is stock! It came with that V8 in it! That "R" on my tires stands for "really old" not radial! Blue gas? We thought it was a pretty color! What wire hooked to my throttle? ... [Read Article]

Latest Ad: Sell 1958 Hi-Altitude Massey Fergerson tractor, original condition. three point hitch pto engine, Runs well, photos available upon request [More Ads]

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy