Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 
Marketplace
Classified Ads
Photo Ads
Tractor Parts
Salvage

Community
Discussion Forums
Project Journals
Your Stories
Events Calendar
Hauling Schedule

Galleries
Tractor Photos
Implement Photos
Vintage Photos
Help Identify
Parts & Pieces
Stuck & Troubled
Vintage Ads
Community Album
Photo Ad Archives

Research & Info
Articles
Tractor Registry
Tip of the Day
Safety Cartoons
Tractor Values
Serial Numbers
Tune-Up Guide
Paint Codes
List Prices
Production Nbrs
Tune-Up Specs
Torque Values
3-Point Specs
Glossary

Miscellaneous
Tractor Games
Just For Kids
Virtual Show
Museum Guide
Memorial Page
Feedback Form

Yesterday's Tractors Facebook Page

  
Tractor Talk Discussion Board

Re: Hydraulic oil filters


[ View Follow Ups ] [ Post Followup ] [ Return to Forum ]

Posted by a mechanic on July 04, 2000 at 13:30:06 from (206.9.216.86):

In Reply to: Hydraulic oil filters posted by Tyler(WA) on June 23, 2000 at 08:03:32:

Filter Basics 101. 1) A spin-on filter should be installed on the return line between the valve and the tank. When the system is on, the pump is always pumping oil at high presure. At idle, the oil has nowhere to go but through the relief valve and back to the tank at low pressure. Locating the filter here ensures that the oil is constantly filtered whenever the system is on. 2) As the filter loads up, it will take a bit of pressure to push the oil through the filter and that's why it must be after the pump. But not in a high pressure line! After the relief valve the pressure drops (most systems below 50psi) and that's plenty to force the oil thru the fiter. It's best to get a filter with a bypass indicator that lets you know when it's time to change it out.
3) If the spin-on filter were installed on the suction side, the pump will cavitate as the filter loads up and eventually the pump will not self-start.
4) A spin-on filter is generally about 10 microns and filters particles you can't see. Its only function is to clean the hydraulic fluid.
5) On the suction side, we still need a filter in front of the pump. Intake filters are typically 100 micron and their only function is to protect
the pump. The openings are large enough that cavitation doesn't occur. This filter is a fine wire mesh affair that is installed inside the tank on the outgoing suction line. These don't need to be changed very often; unless the oil was severely contaminated with large trash you can clean it with compressed air at long intervals. Now of course some tank designs might make installing a suction filter a chore or even an impossibility, so good luck!


Follow Ups:




Post A Followup

:
:

: Re: Re: Hydraulic oil filters

:

:

:

:

: If you check this box, email will be sent to you whenever someone replies to this message. Your email address must be entered above to receive notification. This notification will be cancelled automatically after 2 weeks.


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Today's Featured Article - Women and Tractors - More Views From the Farmer's Wife - by Teri Burkholder. The top ten reasons why the judges wouldn't let you participate in the stock antique tractor pull: Hey, this is stock! It came with that V8 in it! That "R" on my tires stands for "really old" not radial! Blue gas? We thought it was a pretty color! What wire hooked to my throttle? ... [Read Article]

Latest Ad: Sell 1958 Hi-Altitude Massey Fergerson tractor, original condition. three point hitch pto engine, Runs well, photos available upon request [More Ads]

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy