What if I told you that safety chains are for decorations. What would you say to that. Before you say a ting, I will explain. I was a transport truck driver for 13 years, and I have driven pretty well all over North America, both sides of the border. I have seen a lot of accidents, between smaller vehicles pulling trailers, everything from U Hauls, to boats. Most preventable due to safety chains, properly installed, or not. I have also seen dump trucks pulling pup trailers, lose a pup trailer, because the eye broke at the pile. It was loaded with gravel, and it veered off to the right, good thing, the tongue plowed into the shoulder, and flipped end over end into the ditch. Gravel every where, nobody hurt, but was scary on a three lane highway. The safety chains snapped like nothing. Now back to my theory. The trailer manufactures don't put the heaviest safety chains on their trailers. That is why I call them decorations. Every trailer I have purchased, I upgrade my safety chains. If you have seen the things that I have seen, you would too. My boat trailer has a real old, and heavy 12' aluminum boat on it. I put grade 70, 5/16" safety chains, with grade 70 hooks. It had 1/4" light chains on it. I have a 5' x 10' tandem axle, box trailer. It had 5/16 light grade safety chains on it. I put grade 70, 3/8 safety chains with grade 70 hooks. I also have a tandem axle car trailer I converted into a deck over. It had 3/8 light chains, and I installed grade 70 3/8 safety chains with grade 70 hooks. I'm seriously thinking of upgrading to grade 70, 7/16 safety chains and grade 70 hooks, because I haul tractors on it. My own, plus my customers tractors. I've seen wagons loaded with wheat, or corn for whatever reason, leave home with no forwarding address, come UN hooked, and the safety chain failed. I always try to use a safety chains with a heavier safe working load, than what I am actually pulling, on the trailer. I don't use a heaver breaking strength chain for load what I'm pulling an the trailer. That's where I feel there is the problem Trailer manufactures look at the breaking strength of chain, But the chain could have a weaker link in it. That's why I use safe working load. I've always used chains that had a high working load, when I used to haul semi flat bed trailers. I always felt, when a car went by, that could be my family going by, not somebody Else's, and I always wanted to make sure my loads where secure for that reason. My thoughts any way.
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]
Today's Featured Article - Restoration Story: 1951 Farmall H - by The Red (John Fritz). I have been a collector of Farmall tractors since 1990 when I first obtained part of the family farm in Eastern Indiana. My current collection includes a 1938 F20, 1945 H, 1946 H, and the recently purchased 1951 H. This article will focus on what I encountered and what I did to bring the 1951 NEAR DEATH Farmall H back to life.
... [Read Article]
Latest Ad:
Sell 1958 Hi-Altitude Massey Fergerson tractor, original condition. three point hitch pto engine, Runs well, photos available upon request
[More Ads]
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy
TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
