Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 
Marketplace
Classified Ads
Photo Ads
Tractor Parts
Salvage

Community
Discussion Forums
Project Journals
Your Stories
Events Calendar
Hauling Schedule

Galleries
Tractor Photos
Implement Photos
Vintage Photos
Help Identify
Parts & Pieces
Stuck & Troubled
Vintage Ads
Community Album
Photo Ad Archives

Research & Info
Articles
Tractor Registry
Tip of the Day
Safety Cartoons
Tractor Values
Serial Numbers
Tune-Up Guide
Paint Codes
List Prices
Production Nbrs
Tune-Up Specs
Torque Values
3-Point Specs
Glossary

Miscellaneous
Tractor Games
Just For Kids
Virtual Show
Museum Guide
Memorial Page
Feedback Form

Yesterday's Tractors Facebook Page

  
Tractor Talk Discussion Board

Re: Cast wheel wedges


[ Expand ] [ View Replies ] [ Add a Reply ] [ Return to Forum ]

Posted by James Howell on February 28, 2008 at 12:15:38 from (144.162.41.172):

In Reply to: Cast wheel wedges posted by Reder on February 27, 2008 at 16:08:45:

This method of removing stuck wedges worked for me. It has been over 2 years since I removed the wedges from the cast wheels on my JD 70 Diesel pictured below.

third party image

First thing to do is not get in a hurry. Moving wheels in or out might take some time.

Before I worked on these wheels/wedges for the very first time on this tractor, PB Blaster was sprayed on the axle, wedges, and bolts every week at least 3-4 weeks before attempting to “move” the wheel.

If you are not using the tractor, jack up the axle, rotate/turn the wheel, and spray with PB Blaster. Take a small sledge hammer and “tap” on the wedges and bolts. Repeat this process several times. The key word when using the small sledge hammer is “tap”.

I used a rotary grinder with a wire wheel to “brush” the axle on both sides of the wheel.

Loosen the bolts on both wedges.

Turn the wheel so that the “notches” on the axle are on top. There is a pinion on the left side of the cast wheel that you turn with a wrench to move the wheels in or out.

If the wedges are “loose”, turning the pinion will move the wheel in both directions.

Make note of the amount of axle available on the end “away” from the tractor.

Hopefully the wedges are on the inside of the wheel “close” to the tractor.

If the wedges are on the inside of the wheel, remove the bolts on the bottom wedge.

Turn the pinion to move the wheel towards the end of the axle “away” from the tractor.

Since these are “split” wedges, the bottom wedge should be free and fall out.

After removing the wedges, you should finish brushing the axle.

Be careful these wheels/tires are very heavy.

Hope this helps. Good luck!


Replies:




Add a Reply

:
:
:

:

:

:

:

:

:

Advanced Posting Options

: If you check this box, email will be sent to you whenever someone replies to this message. Your email address must be entered above to receive notification. This notification will be cancelled automatically after 2 weeks.



 
Advanced Posting Tools
  Upload Photo  Select Gallery Photo  Attach Serial # List 
Return to Post 

TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Today's Featured Article - The Niagra View Mobile - Powered by a 1959 Ford Tractor - by Mark Massey. In 1959 the Niagara Frontier Transit Inc. of Buffalo, New York designed and built six Viewmobiles for the Niagara Frontier Sightseeing Inc. for use as a sightseeing ride at the Niagara Falls State Park, Niagara Falls, New York, powered by a 1959 Ford 611 Tractor. ... [Read Article]

Latest Ad: Oliver 550 Diesel runs like a watch three point hitch pto engine gone threw about two hundred hours ago nice clean tractor [More Ads]

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy