|
Tractor Talk Discussion Board |
One of those deals.... anyone been there?
[ Expand ] [ View Replies ] [ Add a Reply ] [ Return to Forum ]
Posted by Uh oh on February 21, 2007 at 01:29:41 from (4.244.6.213):
Well, heres part one of my allis C teardown. i know i said allis, but this pertains to all types, and thats why im not in the allis forum. have you ever went to buy a tractor and got the "i totally rebuilt the motor and done it right" deal? Well, i did, and when i heard it run, i believed it. And, of course, i knew the guy and didnt think he would tell me wrong. Dad always said its bad to deal between friends...lol.
Well, the C ran great onto the trailer and off. i knew it had a weld on the side of the block, but had seen no problems from it. Until i got it off the trailer. And then i went to check the oil, or should i say antifreeze in the oil pan. Yeah, i was wrong.
I figured i just as well swap the block, got another and the gasket set and tore into it tonight... started at 9 pm and at 3 a.m. had all the guts out of the engine. The block was busted BAD. And the funny thing is, that "complete rebuild" consisted of a set of rings. Not to say the rest is BAD but it wasnt new with the rings. The sleeves were sanded with a piece of sandpaper, the pistons werent even cleaned up, and the bearings are definantly well used. the governor is even wore all to heck. The temporary fix that was put on this tractor sure made the sale, but like i said, was temporary.
Though its a bit more of a project than i had anticipated, it was still a good deal, all in all, i really didnt get hurt despite what im going to have to put into it. What gets me, however, is how someone can call a set of rings, a few gaskets and a sleeve polishing with good ol' sandpaper a "total rebuild done right". I sure hope this "friend" of mine never becomes a doctor! But my question is, how many of us have fallen into these deals? im sure im not the only one. Guess tomorrow night ill get to work on it some more... ill keep yall updated. i think im gonna just have to perty it up instead of just makin her run good to brush hog. if im gonna put this into it, its a restorer i guess... will look good.
I guess i just needed to gripe a little, but like my good buddy Chris (in-too-deep) once said, "if all the work is done, what fun is it?" Well, Chris... this one is definantly going to be FUN! :) Maybe the reason my "friend" talked me into this was so i would have plenty of fun?!?!?! HAHAHA Could be worse, right?
well, off to bed.... later yall
Replies:
Home
| Forums
Today's Featured Article -
The Nuts and Bolts of Fasteners - Part 2 - by Curtis Von Fange. In our previous article we discussed capscrews, bolts, and nuts along with their relative hardness and thread sizes. In this segment we will finish up on our fasteners and then work with ways to keep them from loosening up in the field. Capscrews, bolts and nuts are not the only means of holding two parts together. When dealing with thinner metals like sheet tin, a long bolt and
... [Read Article]
Latest Ad:
Oliver 550 Diesel runs like a watch three point hitch pto engine gone threw about two hundred hours ago nice clean tractor
[More Ads]
Copyright © 1997-2024 Yesterday's Tractor Co.
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V. Yesterday's Tractors - Antique Tractor HeadquartersWebsite Accessibility Policy |
|
