Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 
Marketplace
Classified Ads
Photo Ads
Tractor Parts
Salvage

Community
Discussion Forums
Project Journals
Your Stories
Events Calendar
Hauling Schedule

Galleries
Tractor Photos
Implement Photos
Vintage Photos
Help Identify
Parts & Pieces
Stuck & Troubled
Vintage Ads
Community Album
Photo Ad Archives

Research & Info
Articles
Tractor Registry
Tip of the Day
Safety Cartoons
Tractor Values
Serial Numbers
Tune-Up Guide
Paint Codes
List Prices
Production Nbrs
Tune-Up Specs
Torque Values
3-Point Specs
Glossary

Miscellaneous
Tractor Games
Just For Kids
Virtual Show
Museum Guide
Memorial Page
Feedback Form

Yesterday's Tractors Facebook Page

  
Tractor Talk Discussion Board

Re: Synthetic Oil Change Interval


[ Expand ] [ View Replies ] [ Add a Reply ] [ Return to Forum ]

Posted by Jon Hagen on February 11, 2007 at 14:44:13 from (75.104.56.247):

In Reply to: Re: Synthetic Oil Change Interval posted by John M on February 11, 2007 at 06:20:50:

My experience with a good POA based synthetic oil like Mobil 1 or Amsoil is that the ring seal is much superior to what is achived with mineral oil. This results in much less blow by garbage getting into the oil to dirty it, The oil does not get dirty nearly as fast, so you can often extend the oil change by 400% and still not have a damaging amount of contaminants in the oil.

Because of this superior ring seal with synthetic oil, oil consumption is often 1/2 or less of what it would be with mineral oil.

One experience with a little Nash 196 engine showed me how even a "hurt" engine can survive for a long time with a superior lubricant in it like Mobil 1.
The Nash 196 has a bad reputation of being an engine with so much crankshaft flex that it is very hard on main bearings. The one I was driving had so much main bearing rumble that it would scare you to rev it up while under the hood. The main journals were worn and really should have been ground to get the journals straight and round, problem was that no undersize bearings were avalible for this obsolete engine. I did manage to find a set of standard bearings to put on the worn crank. The worn crank immediatly started to destroy the new bearings and the main rumble started to return within a few hundred miles. As a bit of a desperate experment, I drained the mineral oil and replaced it with Mobil 1 synthetic oil. This quieted the bearing noise which did not return during the 30,000 miles I put on that old engine over the next dozen years before finally putting the car into storage. In severe operating conditions,like bearings running on a badly worn crank, the POA based synthetic oil really showed how superior a lubricant it is.




Replies:




Add a Reply

:
:
: :

:

:

:

: If you check this box, email will be sent to you whenever someone replies to this message. Your email address must be entered above to receive notification. This notification will be cancelled automatically after 2 weeks.


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Today's Featured Article - Women and Tractors - More Views From the Farmer's Wife - by Teri Burkholder. The top ten reasons why the judges wouldn't let you participate in the stock antique tractor pull: Hey, this is stock! It came with that V8 in it! That "R" on my tires stands for "really old" not radial! Blue gas? We thought it was a pretty color! What wire hooked to my throttle? ... [Read Article]

Latest Ad: Sell 1958 Hi-Altitude Massey Fergerson tractor, original condition. three point hitch pto engine, Runs well, photos available upon request [More Ads]

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy