Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 
Marketplace
Classified Ads
Photo Ads
Tractor Parts
Salvage

Community
Discussion Forums
Project Journals
Your Stories
Events Calendar
Hauling Schedule

Galleries
Tractor Photos
Implement Photos
Vintage Photos
Help Identify
Parts & Pieces
Stuck & Troubled
Vintage Ads
Community Album
Photo Ad Archives

Research & Info
Articles
Tractor Registry
Tip of the Day
Safety Cartoons
Tractor Values
Serial Numbers
Tune-Up Guide
Paint Codes
List Prices
Production Nbrs
Tune-Up Specs
Torque Values
3-Point Specs
Glossary

Miscellaneous
Tractor Games
Just For Kids
Virtual Show
Museum Guide
Memorial Page
Feedback Form

Yesterday's Tractors Facebook Page

  
Tractor Talk Discussion Board

Re: Don't Understand???


[ Expand ] [ View Replies ] [ Add a Reply ] [ Return to Forum ]

Posted by Jon Hagen on January 30, 2007 at 09:53:28 from (69.26.29.104):

In Reply to: Re: Don't Understand??? posted by JOHN HARMON on January 30, 2007 at 09:07:50:

If the noise is just normal wear making parts noisy, then the thicker oil may be the way to go.

I think the point Bob is trying to make is, don't ignore a failing part untill it destroys the transmission.
My experience with that was with a Dodge 3 spd OD trans. This OD transmission is the old Chrysler 4 spd direct drive car transmission modified into an OD transmission. They reworked the gear ratios so you shift 1-2-4 than back to 3 for the OD ratio. The original design of that trans was that you would shift 1-2-3-4 and spend 90% of your time in 4th gear, that couples the input shaft directly to the output shaft. With no load on the gears/bearings during the 90% of the time you are in 4th gear.
When they modified this trans into an overdrive trans, You shift 1-2-4 direct,than back to 3 OD which loads all gears/bearings for 90% of your driving miles.
after 80,000 miles of running 3 OD, the trans developed an ever worsening bearing noise. I pulled the trans and found that the plastic ball cage in the input shaft bearing had worn out from the constant load of the 3 OD gear. Chrysler had discovered the problem,and the $15 replacement bearing had a steel ball cage. Had i continued to ignore the noise, I suspect I would have destroyed the transmission, atleast have broken gears and probibly the case.


Replies:




Add a Reply

:
:
: :

:

:

:

: If you check this box, email will be sent to you whenever someone replies to this message. Your email address must be entered above to receive notification. This notification will be cancelled automatically after 2 weeks.


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Today's Featured Article - Engine Valves - Some Helpful Information - by Staff. Intake - On the intake stroke the piston moves doward, sucking in carburized fuel through the open intake valve. Exhaust valve is closed. Compression - With both the intake and exhaust valves closed, the pistons upward stroke compresses or squeezes the fuel into the combustion chamber. Firing - Ignited by the spark, the compressed fuel explodes and forces the piston downward on its power stroke. Intake and exhaust valves are closed. Exhaust valves and seats are exp ... [Read Article]

Latest Ad: Oliver 550 Diesel runs like a watch three point hitch pto engine gone threw about two hundred hours ago nice clean tractor [More Ads]

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy