Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 
Marketplace
Classified Ads
Photo Ads
Tractor Parts
Salvage

Community
Discussion Forums
Project Journals
Your Stories
Events Calendar
Hauling Schedule

Galleries
Tractor Photos
Implement Photos
Vintage Photos
Help Identify
Parts & Pieces
Stuck & Troubled
Vintage Ads
Community Album
Photo Ad Archives

Research & Info
Articles
Tractor Registry
Tip of the Day
Safety Cartoons
Tractor Values
Serial Numbers
Tune-Up Guide
Paint Codes
List Prices
Production Nbrs
Tune-Up Specs
Torque Values
3-Point Specs
Glossary

Miscellaneous
Tractor Games
Just For Kids
Virtual Show
Museum Guide
Memorial Page
Feedback Form

Yesterday's Tractors Facebook Page

  
Tractor Talk Discussion Board

Re: 1950 Farmall M


[ Expand ] [ View Replies ] [ Add a Reply ] [ Return to Forum ]

Posted by Randy as in Randy-IA on November 26, 2006 at 10:42:16 from (207.177.83.119):

In Reply to: 1950 Farmall M posted by craig aka oliver wendall on November 24, 2006 at 11:14:57:

Hi ! Congrat's on the M ! Some other pointers till your book gets to you . The oil check petcocks are on the side of the oil pan , you want oil to just drip out of the upper one so when you get a good stream of oil out of the lower one while you are filling close it and continue adding oil very slowly till it drips out the top one . A subject that is covered extinsively on the IH forum is leaking oil filter housings . If you change filters make absolutely sure that ALL old o-ring gaskets are removed from the base with a dental pick or small screw driver . Dig in there hard unless you are sure that the restoration was done perfectly . It took me about a half hour of scraping to get all the gasket out of mine it was so hard ! Don't worry , you won't hurt the cast base with a screwdriver or pick . Another point to check is just loosen the final drive oil drain located below the pto shaft , don't remove it so hold on to it as you loosen it up to check for condensation water in the gear oil . This should be done regularly before you operate it after it's sat for a few days . If you get a milky oil out of it then let it sit for as long as possible ( days or even weeks ) and try it again , hopefully the water will seperate from the oil . Otherwise change it ($$$) . 13 gallons of gear lube is what it takes , the book calls for 90w but I think 80w-90 works OK in mine . Look into the drain hole after it's all out with a flashlight and see if there are any chunks of gook in there . It's probably grease chunks from over greasing the axles but try and remove as much as possible anyway with a wire . The final drive and trany filler hole is the big plug under your right foot when you are sitting on the seat . Don't forget to grease the axle ends every couple of uses with a pump or two of grease . Fun tractors and not very high tech . Take care ...Randy


Replies:




Add a Reply

:
:
: :

:

:

:

: If you check this box, email will be sent to you whenever someone replies to this message. Your email address must be entered above to receive notification. This notification will be cancelled automatically after 2 weeks.


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Today's Featured Article - The Nuts and Bolts of Fasteners - Part 2 - by Curtis Von Fange. In our previous article we discussed capscrews, bolts, and nuts along with their relative hardness and thread sizes. In this segment we will finish up on our fasteners and then work with ways to keep them from loosening up in the field. Capscrews, bolts and nuts are not the only means of holding two parts together. When dealing with thinner metals like sheet tin, a long bolt and ... [Read Article]

Latest Ad: Oliver 550 Diesel runs like a watch three point hitch pto engine gone threw about two hundred hours ago nice clean tractor [More Ads]

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy