Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 
Marketplace
Classified Ads
Photo Ads
Tractor Parts
Salvage

Community
Discussion Forums
Project Journals
Your Stories
Events Calendar
Hauling Schedule

Galleries
Tractor Photos
Implement Photos
Vintage Photos
Help Identify
Parts & Pieces
Stuck & Troubled
Vintage Ads
Community Album
Photo Ad Archives

Research & Info
Articles
Tractor Registry
Tip of the Day
Safety Cartoons
Tractor Values
Serial Numbers
Tune-Up Guide
Paint Codes
List Prices
Production Nbrs
Tune-Up Specs
Torque Values
3-Point Specs
Glossary

Miscellaneous
Tractor Games
Just For Kids
Virtual Show
Museum Guide
Memorial Page
Feedback Form

Yesterday's Tractors Facebook Page

  
Tractor Talk Discussion Board

Re: WHAT will we do - a long read


[ Expand ] [ View Replies ] [ Add a Reply ] [ Return to Forum ]

Posted by williamf on November 15, 2006 at 05:14:46 from (66.82.9.53):

In Reply to: WHAT will we do posted by No tools on November 15, 2006 at 03:51:47:

It'll rain this evening here, too. So this morning I'll go down in the swamp to finish the little bit of road work I was on Monday when the hydraulic line sprung a leak.
Which covers what I did yesterday. And Monday.
It's the second time I've replaced that hose, and the one next to it that goes to the other end of the same cylinder twice also. After I replaced the other the second time I admitted that I understood some things better than the designers and didn't put it back in the clamp. Engineers hate to see a hydraulic hose move along its length but sometimes that's better than having it crimp and twist where it's held tight.
If I had gone back and liberated this one at the same time I would have had to find something else to keep myself busy today.
It's a serious chore to replace one of these; this one required taking the seat off and taking loose six other hoses to get to the end up under the platform. All of them hard to reach. Put the wrench on, turn the tiniest fraction, take the wrench out, move around to the other side of the tractor, climb up and twist around to reach, insert the wrench though another hole, turn another tiny fraction, climb back down, go back to the first hole and insert a different wrench, another miniscule movement.... The only thing that kept me going was knowing I had done it before so it had to be possible. I was younger then, though.
It took eight hours actual work time and two trips to town.
The bright spots: I replaced the ends on two of the really difficult hoses - they were male ends that required turning the whole hose to unscrew them. With to 90* turns in the hose that's a job for three hands.
Also, by chance I wore a t-shirt from the mill where I work to the hydraulic service place. Turns out the counter guy did a lot of business with the maintenence folks in my department, we knew a lot of the same people, when he wrote up my bill he gave me the same discount IP gets. Bill was half what I expected.
It's who you know.
Better day today and much needed rain tonight.
Wm





Replies:




Add a Reply

:
:
: :

:

:

:

: If you check this box, email will be sent to you whenever someone replies to this message. Your email address must be entered above to receive notification. This notification will be cancelled automatically after 2 weeks.


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Today's Featured Article - The Nuts and Bolts of Fasteners - Part 2 - by Curtis Von Fange. In our previous article we discussed capscrews, bolts, and nuts along with their relative hardness and thread sizes. In this segment we will finish up on our fasteners and then work with ways to keep them from loosening up in the field. Capscrews, bolts and nuts are not the only means of holding two parts together. When dealing with thinner metals like sheet tin, a long bolt and ... [Read Article]

Latest Ad: Oliver 550 Diesel runs like a watch three point hitch pto engine gone threw about two hundred hours ago nice clean tractor [More Ads]

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy