Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 
Marketplace
Classified Ads
Photo Ads
Tractor Parts
Salvage

Community
Discussion Forums
Project Journals
Your Stories
Events Calendar
Hauling Schedule

Galleries
Tractor Photos
Implement Photos
Vintage Photos
Help Identify
Parts & Pieces
Stuck & Troubled
Vintage Ads
Community Album
Photo Ad Archives

Research & Info
Articles
Tractor Registry
Tip of the Day
Safety Cartoons
Tractor Values
Serial Numbers
Tune-Up Guide
Paint Codes
List Prices
Production Nbrs
Tune-Up Specs
Torque Values
3-Point Specs
Glossary

Miscellaneous
Tractor Games
Just For Kids
Virtual Show
Museum Guide
Memorial Page
Feedback Form

Yesterday's Tractors Facebook Page

  
Tractor Talk Discussion Board

Re: 706 D PTO


[ Expand ] [ View Replies ] [ Add a Reply ] [ Return to Forum ]

Posted by the tractor vet on November 11, 2006 at 17:55:55 from (75.19.127.158):

In Reply to: 706 D PTO posted by Big un on November 11, 2006 at 13:46:03:

Well now if it was me first i would check the pressures on it first. , But this takes a special fitting and a gauges that will read 600PSI . You adjust pressure by turning the valve stem in for more and out for less BUT YA GOT TO HAVE THE GAUGE . As far as changing out the clutch pack about a couple hours because ya have to drain the rear end , ya also need a cherry picker to handel the pto as when you are comming out you must tip the rear of the pto down for the pickup tube to clear . then it is just a matter of popen out a large snap ring . But here is the kicker when ya have it out it is wise to REBUILD the whole unit . Now ya may have some leakage around the teflon seal rings or a wore out hub and loosen pressure there or a leaking O/RING in the clutch pack . HEre ya have to have a couple special tools to compress the drun down against the brake springs and releive pressure on the return spring and if you are handie ya can make up a spring compressor out of a pice of heavy plate two pices of all thread and a pice of pipe with a cutout to give acess to the snaprings. . IT takes me anywhere from three and a half to four and a half hours to rebuid one from start to finish and that includes doing a Hot set on the pressureas ya can not set it with cold oil and get it wright.When i do one i always change out the stock clutch pac for the heavy duty one and set pressure at between 245 and 265.


Replies:




Add a Reply

:
:
: :

:

:

:

: If you check this box, email will be sent to you whenever someone replies to this message. Your email address must be entered above to receive notification. This notification will be cancelled automatically after 2 weeks.


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Today's Featured Article - The Day Mom Drove the 8N - by Brian Browning. My Dad was wanting to put in a garden but couldn't operate the 8N and handle the old horse drawn plow he had found and rigged up to use with the tractor. Well, he decided to go get Mom out of the house and have her drive the tractor while he walked behind the plow. You got to understand that while my Mom is a hard worker who will always help whenever she can... she had never operated farm machinery before that day. Dad got her out there, explained how the clutch was the same as in our o ... [Read Article]

Latest Ad: Oliver 550 Diesel runs like a watch three point hitch pto engine gone threw about two hundred hours ago nice clean tractor [More Ads]

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy