Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 
Marketplace
Classified Ads
Photo Ads
Tractor Parts
Salvage

Community
Discussion Forums
Project Journals
Your Stories
Events Calendar
Hauling Schedule

Galleries
Tractor Photos
Implement Photos
Vintage Photos
Help Identify
Parts & Pieces
Stuck & Troubled
Vintage Ads
Community Album
Photo Ad Archives

Research & Info
Articles
Tractor Registry
Tip of the Day
Safety Cartoons
Tractor Values
Serial Numbers
Tune-Up Guide
Paint Codes
List Prices
Production Nbrs
Tune-Up Specs
Torque Values
3-Point Specs
Glossary

Miscellaneous
Tractor Games
Just For Kids
Virtual Show
Museum Guide
Memorial Page
Feedback Form

Yesterday's Tractors Facebook Page

  
Tractor Talk Discussion Board

Re: Yes


[ Expand ] [ View Replies ] [ Add a Reply ] [ Return to Forum ]

Posted by jdemaris on November 09, 2006 at 19:22:51 from (69.67.229.114):

In Reply to: Re: Spark plug gap question posted by B-maniac on November 09, 2006 at 18:28:55:

Absolutely correct. That's why high-energy ignition systems with wide plug gaps need better wires as well as other parts.
I just had a situation that created its own high-engergy ignition by accident. Hunting camp near me has a 1978 Chevy Blazer used for carting around deer hunters. It got running bad - I took at look at it for them. I found - in the inside of the distributor cap - just a burn-hole where the spring-loaded conductor-pole is supposed to be. It was supposed to rub against the rotating rotor - and it's conductor piece was also completely burnt off and gone. So - spark was jumping a huge gap to get to the plug wires - at least a 1/2". Truck broke up and ran terrible - but did run and I could drive it. Well - I "fixed it" by installing a new cap and rotor - and then - it would not run at all - except for one cylinder firing out of eight (350 V8). Long story short the plugs were all fouled - but with the burnt-out cap and rotor - voltage got so high they fired. Once I fixed it, it did not. This really threw me for a little while - but I put new plugs in it - and it was then fine.
On a similar note - I still have my Honda CL175 motorcycle - ca. 1972. It has a two-cylinder engine - but for one year - Honda used an ignition with a single set of points, and one coil with two secondaries (plug wires). I assume it was designed to always fire both plugs every stroke. Problem is - and has been since new - when cold - only one cylinder will fire - and it can be either one - you never know. So, I pull the plug wife off the one that is not firing, and slowly pull it away - with the engine running. A spark will jump - and get longer as I pull away - and when I get to a certain distance - that cylinder begins to fire - and then both are running. Once it warms up a little, all is fine. The next year of production for the bike, Honda changed over to dual points and dual coils - so I suspect they recognized a problem.
And - how far can you go? I just found out with my wife's neglected 1995 Subaru Impreza. Just hit 135,000 miles and it's never had spark plugs. It has no distributor or cap - and since it's always ran great - never got plugs. A few mornings ago - it wouldn't start - but "almost" did when I let off the key. First reaction - I got mad at the car. Then I remembered - it's had oil changes and timing belts - but never spark plugs. I pulled them out - the gap was so wide - my plug gapper could not measure - but around a 1/4". Must be the breaking-point where the voltage cannot jump the gap. Other than that, the plugs looked like new. I closed the gaps to .045", and now - all is fine again.


Replies:

  • Re: Yes oldcraneguy 10:52:11 11/10/06 (0)



Add a Reply

:
:
: :

:

:

:

: If you check this box, email will be sent to you whenever someone replies to this message. Your email address must be entered above to receive notification. This notification will be cancelled automatically after 2 weeks.


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Today's Featured Article - Talk of the Town: The Saga of Grandpa's Tractor - by The following saga is from the Tractor Talk Discussion Forum. Someone. The saga starts with the following message: Hey guys I have a decision to make. I know what you all will probably suggest and it will probably agree with me way down inside, but here it is. I have a picture blown up and framed in my "tractor room" of a Farmall M. It was my Grandpa's tractor, of which whom I never got to meet. He froze to death getting this tractor out of the barn to pull a truck out of the ditch before I was born. Anyway my dad and aunt had to sell it at the auction, ... [Read Article]

Latest Ad: Sell 1958 Hi-Altitude Massey Fergerson tractor, original condition. three point hitch pto engine, Runs well, photos available upon request [More Ads]

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy