Re: Ford 9N specs

Posted by MLP on October 27, 2006 at 07:55:35 from (213.239.210.120):

In Reply to: Ford 9N specs posted by Jim Gordon on October 26, 2006 at 17:38:58:

This is from the Smith's 8N Ford Tractor page
Hope it helps
8N Specifications and Data

General
Wheelbase . . . . . . . . . . . . . . . . . . . . . . . . . . 70 inches
Over-all length . . . . . . . . . . . . . . . . . . . . . . 115 inches
Over-all height . . . . . . . . . . . . . . . . . . . 54 1/2 inches
Over-all width, normal tread . . . . . . . . 64 3/4 inches
Tire size:
Front standard . . . . . . . . . . . . . . . . . . . . . 4.00 - 19
optional . . . . . . . . . . . . . . . . . . . . . . 6.00 - 16
Rear standard. . . . . . . . . . . . . . . . . . . . . . . 11.2 - 28
Tread width . . . . . . . . .48 to 76 inches in 4-inch steps
Turning circle radius (with use of brakes):
Made by outer front wheel . . . . . . . . . . . . . . . . 8 ft.
Made by tractor centerline at rear axle . . 3 1/2 ft.
Shipping weight (including gasoline, oil, water, tires
with air, operator not included) . . . . . . . . 2,410 lbs.
Drawbar height . . . . . . . . . . . . . . . 8 1/2 to 34 1/4 in.
Capacities - U.S. Measure
Fuel tank . . . . . . . . . . . . . . . . . . . . . . . . . 10 gals. total
Engine oil pan. . . . . . . . . . . . . . . . . . . 6 qts. with filter
Transmission, hydraulics 80w90 . . . . . . . . . . . . 5 gals.
Cooling system . . . . . . . . . . . . . . . . . . . . . . . . . . 12 qts.
Oil bath air cleaner. . . . . . . . . . . . . . . . . . . . . . . 1 pint
Tire pressure:
Rear . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 lbs.
Front . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 lbs.
Engine
Type . . . . . . . . . . . . . . . . . . . . . . . 4-cylinder "L" head
Maximum Drawbar HP. 2nd Gear. . . . . . . . . . . . . 23.16
Maximun belt horsepower at 2000 R.P.M. . . . . . 27.32
Rated speeds . . . . . . . . . . 1500, 1750, and 2000 RPM.
Idle speed . . . . . . . . . . . . . . . . . . . . . . 400-450 R.P.M.
Cylinder bore. . . . . . . . . . . . . . . . . . . . . . . . . . 3.188 in.
Stroke . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.75 in.
Piston displacement . . . . . . . . . . . . . . . . . . . 119.7 cu. in.
Torque . . . . . . . . . . . . . . . . . . . . 92 lbs ft. at 1500 rpm
Compression ratio. . . . . . . . . . . . . . . . . . . . . . . . . 6.50:1
Sleeves. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Dry type
Piston. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Aluminum
Rings. . . . . . . . . . . . . . . . . . . . Compression (2) Oil (1)
Piston pin . . . . . . . . . . . . . . . . . . . . . . . . . . Full floating
Rod bearings . . . . . . . . . . . . . . . Replaceable shell-type
Main bearings . . . . . . . . . . . . . . Replaceable shell-type
Crankshaft . . . Cast steel, static and dynamic balanced
Compression psi at cranking speed . . . . 90 psi minimum
Valve tappet clearance:
Intake . . . . . . . . . . . . . . . . . . . . . . . . .010 - .012 cold
Exhaust . . . . . . . . . . . . . . . . . . . . . . . .014 - .016 cold
Crankshaft journal:
Main bearing diameter . . . . . . . . . . 2.248 - 2.249 in.
Rod bearing diameter. . . . . . . . . . . . . . . . . . 2.094 in.

Tread width is 48" to 76".

I have two more pages if you whant more info.

Replies:

Add a Reply Name: E-Mail: Subject: Comments: Optional Link URL: Link Title: Optional Image URL: Email Notification: If you check this box, email will be sent to you whenever someone replies to this message. Your email address must be entered above to receive notification. This notification will be cancelled automatically after 2 weeks.

TRACTOR PARTS	TRACTOR MANUALS

We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]