Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 
Marketplace
Classified Ads
Photo Ads
Tractor Parts
Salvage

Community
Discussion Forums
Project Journals
Your Stories
Events Calendar
Hauling Schedule

Galleries
Tractor Photos
Implement Photos
Vintage Photos
Help Identify
Parts & Pieces
Stuck & Troubled
Vintage Ads
Community Album
Photo Ad Archives

Research & Info
Articles
Tractor Registry
Tip of the Day
Safety Cartoons
Tractor Values
Serial Numbers
Tune-Up Guide
Paint Codes
List Prices
Production Nbrs
Tune-Up Specs
Torque Values
3-Point Specs
Glossary

Miscellaneous
Tractor Games
Just For Kids
Virtual Show
Museum Guide
Memorial Page
Feedback Form

Yesterday's Tractors Facebook Page

  
Tractor Talk Discussion Board

Re: O/T: '95 Escort axles


[ Expand ] [ View Replies ] [ Add a Reply ] [ Return to Forum ]

Posted by rgvtx on August 28, 2006 at 15:47:53 from (205.188.117.14):

In Reply to: O/T: '95 Escort axles posted by MeAnthony on August 28, 2006 at 14:38:41:

Hi Anthony,
I had an Escort at one time and still have the manual for it, but can't find it at the moment. Anyway, did a quick Google search and found this info. The link to the whole article will be included below.
HTH, and good luck!

~Remove both front tires because we will need to get to the rotors and axles.

Ok, you are gonna be wondering why, but we have to unbolt the rotors (round disc's that attach to the rims). Unbolt these with 2 bolts from the bottom. They are attached to what’s called a control arm. So, starting from the driver's side, un bolt the two bolts. Then have someone lift up on the rotor while u pushes down on the control arm. This separates the rotor from the control arm. Once this is done, you need to have someone pull back on the rotor(BE CAREFUL NOT TO PULL TOO HARD, pull back far, just do it gradually) while you pry on the axle with a pry bar. YOU PRY INBETWEEN THE CV JOINT AND THE TRANSMISSION. DO NOT PUT CONSTANT FORCE ON IT. JUST PUMP ON IT A FEW TIMES TILL IT COMES OUT. It might take a little elbow grease from both of you, but the axle will come out. If you didn’t drain the transmission, right now your face or clothes will be gettin drenched. Next, you need to get the other axle out. This is kinda tricky. Follow the same procedure to get the rotor off with one exception. You will actually have to remove a bolt that attaches the axle to the rotor. It’s found on the front center of the rotor. First unbolt the Wheel hub from the Control arm like you did on the driver's side. This side is a little different. The axle is in 2 pieces on this side. Unbot the axle mount that bolts to the back of the engine. Let this bracket dangle where it wants. Its attached to the axle, so you wont lose it or anything. Once you have the center cap removed from the rotor, Remove the axle from the rotor by pulling back once again on the rotor. on this side. Then pull the axle off from the other side. Then, pull that part out of the transmission. This side isnt locked in like the driver's side so it will just pop out when you pull on the axle.~



Replies:




Add a Reply

:
:
: :

:

:

:

: If you check this box, email will be sent to you whenever someone replies to this message. Your email address must be entered above to receive notification. This notification will be cancelled automatically after 2 weeks.


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Today's Featured Article - Engine Valves - Some Helpful Information - by Staff. Intake - On the intake stroke the piston moves doward, sucking in carburized fuel through the open intake valve. Exhaust valve is closed. Compression - With both the intake and exhaust valves closed, the pistons upward stroke compresses or squeezes the fuel into the combustion chamber. Firing - Ignited by the spark, the compressed fuel explodes and forces the piston downward on its power stroke. Intake and exhaust valves are closed. Exhaust valves and seats are exp ... [Read Article]

Latest Ad: Oliver 550 Diesel runs like a watch three point hitch pto engine gone threw about two hundred hours ago nice clean tractor [More Ads]

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy