Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 
Marketplace
Classified Ads
Photo Ads
Tractor Parts
Salvage

Community
Discussion Forums
Project Journals
Your Stories
Events Calendar
Hauling Schedule

Galleries
Tractor Photos
Implement Photos
Vintage Photos
Help Identify
Parts & Pieces
Stuck & Troubled
Vintage Ads
Community Album
Photo Ad Archives

Research & Info
Articles
Tractor Registry
Tip of the Day
Safety Cartoons
Tractor Values
Serial Numbers
Tune-Up Guide
Paint Codes
List Prices
Production Nbrs
Tune-Up Specs
Torque Values
3-Point Specs
Glossary

Miscellaneous
Tractor Games
Just For Kids
Virtual Show
Museum Guide
Memorial Page
Feedback Form

Yesterday's Tractors Facebook Page

  
Tractor Talk Discussion Board

Broken Manifold Bolts refresher course


[ Expand ] [ View Replies ] [ Add a Reply ] [ Return to Forum ]

Posted by Billy NY on February 14, 2006 at 17:38:55 from (64.12.116.74):

I've been reading up on this subject, as while attempting a quick fix on this 292 in the old F-600, I found the weak one ! There's always one, good thing is there will be 3/8" -1/2" protruding.

BTW, the furnace cement held great, sealed the crack, but that was not the leak, so I'm taking it off, just too annoying to listen to anymore.

I am wary about welding a nut on as I don't want to arc the crank bearings,not a lot of room,maybe take the inner fender well off, but having a grip and the heat would do it, I'm just not confident about where to clamp the ground. I've got some industrial penetrating oil, Free-All, and can apply heat with oxy/acetylene or just acetylene, little cooler. I'll try getting a bite with vise grips, I know Snap On makes a tool for this also, + hammering on the end to vibrate and break the bond. Just read one about where they hooked the hot, stinger to the stud and grounded nearby, then gave it the juice for 2 seconds, heat broke it free, I dunno if I'd try that. All the other bolts are loose, odds are it's not seized that bad, possibly some heat, light hammering to break the bond and if I can get a grip it may come out. I've done flush ones before, know the drilling procedures also know the dangers of E-Z outs, etc. Also reverse bits etc. Lot of tricks out there, but was really wondering how people here tackle these ?


Replies:




Add a Reply

:
:
:

:

:

:

:

: If you check this box, email will be sent to you whenever someone replies to this message. Your email address must be entered above to receive notification. This notification will be cancelled automatically after 2 weeks.


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Today's Featured Article - The Niagra View Mobile - Powered by a 1959 Ford Tractor - by Mark Massey. In 1959 the Niagara Frontier Transit Inc. of Buffalo, New York designed and built six Viewmobiles for the Niagara Frontier Sightseeing Inc. for use as a sightseeing ride at the Niagara Falls State Park, Niagara Falls, New York, powered by a 1959 Ford 611 Tractor. ... [Read Article]

Latest Ad: Oliver 550 Diesel runs like a watch three point hitch pto engine gone threw about two hundred hours ago nice clean tractor [More Ads]

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy