Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 
Marketplace
Classified Ads
Photo Ads
Tractor Parts
Salvage

Community
Discussion Forums
Project Journals
Your Stories
Events Calendar
Hauling Schedule

Galleries
Tractor Photos
Implement Photos
Vintage Photos
Help Identify
Parts & Pieces
Stuck & Troubled
Vintage Ads
Community Album
Photo Ad Archives

Research & Info
Articles
Tractor Registry
Tip of the Day
Safety Cartoons
Tractor Values
Serial Numbers
Tune-Up Guide
Paint Codes
List Prices
Production Nbrs
Tune-Up Specs
Torque Values
3-Point Specs
Glossary

Miscellaneous
Tractor Games
Just For Kids
Virtual Show
Museum Guide
Memorial Page
Feedback Form

Yesterday's Tractors Facebook Page

  
Tractor Talk Discussion Board

Allis Chalmers B engine


[ Expand ] [ View Follow Ups ] [ Post Followup ] [ Return to Forum ]

Posted by wdtom on November 20, 2005 at 16:43:35 from (155.212.222.112):

Saturday while pulling a trailer with fire wood with our AC-B my brother and I noticed a rapping or knocking in what turned out to be the engine. Within a hundred yards of going along in third it went from "do I hear anything or is it just some odd rattle" to "I don't want to run this engine anymore until I fix whatever is making that noise". I stopped the tractor, my brother got off the trailer and went around to the side of the engine and told me the sound is comming from the engine, it was loud enough that I shut it off at this point and we towed it back to the house. The long and short of it is that we ended up with the engine on an engine stand and the pan off, could find nothing by looking and feeling for play. Next day we started pulling and checking rods, found one that the upper bearing shell was just comming apart. This engine has been a good runner, strong, with good oil pressure, which we keep clean oil in. There were no knocks until this failure. Before we owned it the original owner had it since new, using it for mostly snowplowing. From the look of the engine and measurements of crank, it had never been worked on since new, probably around 1950. Anybody know what might make a bearing fail like this? On the front half of the upper shell the metal surface was mostly gone, on the rear half it had cracks running back and a few pieces of the surface were gone. I am glad I shut it down when I did. Crank looked good, rod surfaces miked out within new except for the bad one which was .0008" out of round. Mains were round but .004" worn. Will be grinding crank and installing new bearings.


Follow Ups:




Post a Followup

:
:
:

:

:

:

:

: If you check this box, email will be sent to you whenever someone replies to this message. Your email address must be entered above to receive notification. This notification will be cancelled automatically after 2 weeks.


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Today's Featured Article - The Niagra View Mobile - Powered by a 1959 Ford Tractor - by Mark Massey. In 1959 the Niagara Frontier Transit Inc. of Buffalo, New York designed and built six Viewmobiles for the Niagara Frontier Sightseeing Inc. for use as a sightseeing ride at the Niagara Falls State Park, Niagara Falls, New York, powered by a 1959 Ford 611 Tractor. ... [Read Article]

Latest Ad: Oliver 550 Diesel runs like a watch three point hitch pto engine gone threw about two hundred hours ago nice clean tractor [More Ads]

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy