Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 
Marketplace
Classified Ads
Photo Ads
Tractor Parts
Salvage

Community
Discussion Forums
Project Journals
Your Stories
Events Calendar
Hauling Schedule

Galleries
Tractor Photos
Implement Photos
Vintage Photos
Help Identify
Parts & Pieces
Stuck & Troubled
Vintage Ads
Community Album
Photo Ad Archives

Research & Info
Articles
Tractor Registry
Tip of the Day
Safety Cartoons
Tractor Values
Serial Numbers
Tune-Up Guide
Paint Codes
List Prices
Production Nbrs
Tune-Up Specs
Torque Values
3-Point Specs
Glossary

Miscellaneous
Tractor Games
Just For Kids
Virtual Show
Museum Guide
Memorial Page
Feedback Form

Yesterday's Tractors Facebook Page

  
Tractor Talk Discussion Board

Re: Safety? You gotta be kidding!


[ Expand ] [ View Follow Ups ] [ Post Followup ] [ Return to Forum ]

Posted by jdemaris on September 30, 2005 at 07:27:50 from (66.218.28.187):

In Reply to: Re: Safety? You gotta be kidding! posted by buickanddeere on September 30, 2005 at 07:07:45:

I'm okay now. I didn't think I was going to walk again during the first 6 months - or be able to talk - but I recovered all right. I've got lots of steel in me now and it hurts like H*ll, but that's the way it goes. Sometimes I think most of the damage is in my brain - but those that know me say I've always been like this.
I've been in two bad tractor accidents, both my fault as I see it. I was run over by a Massey Ferguson back in the 70s - after I hotwired the neutral safety-switch for the owner. I stood there, warning him how dangerous it could be - and commenced to start it (while in 1st gear). It went write over me - broke my arm and ribs. That was about the stupidest thing I've ever done.
Years later, with the 3020 accident - I also take full credit for that. I've worked on Deere equuipment most of my life, so the shortcomings of the 2520-3020-4020 steering and brakes were no secret to me. I was moving equipment with my IH tractor, and my neighbor urged me to borrow his 3020 - since it was bigger and faster. The tractor was in very poor condiditon, I did NOT want to use it, but in an effort not to hurt his feelings, used it anyway. BIG MISTAKE. So, I knew better but did it anyway and d*mn near killed myself.
As I said before, Deere had a very bad system for brakes and steering - but it was no secret. I am in charge of my own safety, not some tractor company.




Follow Ups:




Post a Followup

:
:
: :

:

:

:

: If you check this box, email will be sent to you whenever someone replies to this message. Your email address must be entered above to receive notification. This notification will be cancelled automatically after 2 weeks.


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Today's Featured Article - Third Brush Generators - by Chris Pratt. While I love straightening sheet metal, cleaning, and painting old tractors, I use every excuse to avoid working on the on the electrics. I find the whole process sheer mystery. I have picked up and attempted to read every auto and farm electrics book with no improvement in the situation. They all seem to start with a chapter entitled "Theory of Electricity". After a few paragraphs I usually close the book and go back to banging out dents. A good friend and I were recently discussing our tractor electrical systems when he stated "I figure it all comes back to applying Ohms Law". At this point ... [Read Article]

Latest Ad: John Deere B 1943 [More Ads]

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy