Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 
Marketplace
Classified Ads
Photo Ads
Tractor Parts
Salvage

Community
Discussion Forums
Project Journals
Your Stories
Events Calendar
Hauling Schedule

Galleries
Tractor Photos
Implement Photos
Vintage Photos
Help Identify
Parts & Pieces
Stuck & Troubled
Vintage Ads
Community Album
Photo Ad Archives

Research & Info
Articles
Tractor Registry
Tip of the Day
Safety Cartoons
Tractor Values
Serial Numbers
Tune-Up Guide
Paint Codes
List Prices
Production Nbrs
Tune-Up Specs
Torque Values
3-Point Specs
Glossary

Miscellaneous
Tractor Games
Just For Kids
Virtual Show
Museum Guide
Memorial Page
Feedback Form

Yesterday's Tractors Facebook Page

  
Tractor Talk Discussion Board

Re: Somebody talk me out of it - trailer purchase


[ Expand ] [ View Follow Ups ] [ Post Followup ] [ Return to Forum ]

Posted by T_Bone on July 27, 2005 at 11:42:02 from (4.240.42.5):

In Reply to: Somebody talk me out of it - trailer purchase posted by wirehair on July 27, 2005 at 06:29:35:

Hi wirhair,

After pulling trailers for 40yrs, I've learned thru the school of hard knocks that you will never have enough trailer unless you break down and buy/build the one trailer that you will ever need.

I did that this year as I bought a new 20kGVW 27ft + 5ft dovetail, Dexter dual tandum oil bath 10K axles, 19# I-beam with 3" channel cross beams on 16" centers, 6" torque tube, 6" edge channel with a 2-1/2" x 3/8" rub rail, 20" sping assist ramps, Bulldog GN, for $6400 out the door and $200 lower than my material cost for the same.

Shorter trailers equiped the same was about $5100 and $600 deliverly.

Now I can get rid of my 28ft flated bumper pull, won't haul enough weight, and my 18ft + 4ft dovetail flatbed tri-axle pintel, that has no load sweet spot due to being a tri-axle and again since a bumper pull, limited load weight. Don't exceed bumper pull hitch ratings as there barely adaquote as it is and I have custom built hitching.

After one pull with my new trailer, I can see I should have bought/built this trailer many years ago. Increased load stability from the DRW alxes, increased braking capibility, I-beam frame for long lasting strength on rolling loads, torque tube for front deck stability without frame twisting, easy to lift ramps.

Cut your loss now and buy the correct trailer that will last you a life time. You will save money in the long run.

T_Bone


Follow Ups:




Post a Followup

:
:
: :

:

:

:

: If you check this box, email will be sent to you whenever someone replies to this message. Your email address must be entered above to receive notification. This notification will be cancelled automatically after 2 weeks.


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Today's Featured Article - The Nuts and Bolts of Fasteners - Part 2 - by Curtis Von Fange. In our previous article we discussed capscrews, bolts, and nuts along with their relative hardness and thread sizes. In this segment we will finish up on our fasteners and then work with ways to keep them from loosening up in the field. Capscrews, bolts and nuts are not the only means of holding two parts together. When dealing with thinner metals like sheet tin, a long bolt and ... [Read Article]

Latest Ad: Oliver 550 Diesel runs like a watch three point hitch pto engine gone threw about two hundred hours ago nice clean tractor [More Ads]

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy