Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 
Marketplace
Classified Ads
Photo Ads
Tractor Parts
Salvage

Community
Discussion Forums
Project Journals
Your Stories
Events Calendar
Hauling Schedule

Galleries
Tractor Photos
Implement Photos
Vintage Photos
Help Identify
Parts & Pieces
Stuck & Troubled
Vintage Ads
Community Album
Photo Ad Archives

Research & Info
Articles
Tractor Registry
Tip of the Day
Safety Cartoons
Tractor Values
Serial Numbers
Tune-Up Guide
Paint Codes
List Prices
Production Nbrs
Tune-Up Specs
Torque Values
3-Point Specs
Glossary

Miscellaneous
Tractor Games
Just For Kids
Virtual Show
Museum Guide
Memorial Page
Feedback Form

Yesterday's Tractors Facebook Page

  
Tractor Talk Discussion Board

Rock Shaft Trouble, Ford 3600


[ Expand ] [ View Follow Ups ] [ Post Followup ] [ Return to Forum ]

Posted by Kirk Grau on May 26, 2005 at 11:44:58 from (68.67.222.211):

Hi Everybody,

I posted on this a couple of days ago now I need help/info. The screw and large washer that holds the rockshaft in place came loose from one end of the shaft while I was mowing last weekend. By the time I noticed it the rockshaft had vibrated quite a way out the other end. It went far enough that the splines that engage the lift arm internally have lost their alignment. I have ordered the parts that are missing out in the field and expect them tomorrow. I have tried to get the rock shaft aligned and back through without actually removing the lift. Had I been successful at it I would not be writing this now. I think I am going to have to remove the whole lift assembly to get the shaft back in. I have an exploded diagram of the shaft assembly from my local parts department and see that there is a thrust washer somewhere in the assembly. I think that is probably what is keeping me from getting things lined up again.

Now to my question. What is going to happen when I loosen up the lift assembly? Can I just pull it out and go? How about the hydraulic controls? They are mounted to the top of the lift assembly also. Can I take them off to get access to the bolts underneath without doing some major surgery?

I can always get the dealer to fix it, but he is backed up about 2 weeks and I need to use the tractor before then. Besides I kind of enjoy turning a wrench once in a while. I just am not very familiar with the hydraulic stuff on tractors.

Thanks,

Kirk


Follow Ups:




Post a Followup

:
:
:

:

:

:

:

: If you check this box, email will be sent to you whenever someone replies to this message. Your email address must be entered above to receive notification. This notification will be cancelled automatically after 2 weeks.


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Today's Featured Article - The Nuts and Bolts of Fasteners - Part 2 - by Curtis Von Fange. In our previous article we discussed capscrews, bolts, and nuts along with their relative hardness and thread sizes. In this segment we will finish up on our fasteners and then work with ways to keep them from loosening up in the field. Capscrews, bolts and nuts are not the only means of holding two parts together. When dealing with thinner metals like sheet tin, a long bolt and ... [Read Article]

Latest Ad: Oliver 550 Diesel runs like a watch three point hitch pto engine gone threw about two hundred hours ago nice clean tractor [More Ads]

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy