Tractor Talk Discussion Board |
Re:Tractor Flips
[ Expand ] [ View Follow Ups ] [ Post Followup ] [ Return to Forum ]
Posted by JoeK on February 16, 2005 at 07:25:01 from (207.230.218.66):
Not to beat a horse to death,but I feel that besides lack of experience/knowledge of safe operations,a major factor can be modifications that commonly occur.Now to start with,I grew up with Fergies and Fords and Pop had me draggin wagons and rakin hay with a 9N by 2nd grade.Until my teens,we never had a tractor with a rigid drawbar,just the 3pt,BUT always used with stabilizer links.We also drug firewood and pulp logs,sometimes using ARP traks,but I don't recall ever having a near miss flipover. Tractors were designed to a specification,ie:the Ns were designed to pull a two bottom plow or equivelant load as built.However the whole equation changes with bigger tires,fluid weight,wheel weights added to reduce slippage or make the tractor"exceed it's design".When a tractor spins out attempting a task,it has exceeded it's "design"capability.Adding massive weight to the rears does increase it's capability,but at some cost to safety as more traction causes more likelyhood of rearing,than spinning out.It's a fine point of balance that only experience teaches.Picking the wrong gear for the load is important too.While 1st may be the way to go on a stock/unloaded tractor,with fluid/weights maybe you'd be better to use a higher gear/less throttle(better to lug the engine,than flip the tractor),mebbe chains(not used cuz they're a bother)would be the way to go,rather than weight.I see too many "yuppie bait"used tractors on the lots with 1/2 ton of iron hangin on em.My eye says used/abused,not"tough tractor".In short,all I'm sayin is that any driveline mods,weight/tiresize/hp can all change the behavior of the tractor.And of course"proper tool for the job"means though you MAY be able to drive rail spikes with a tack hammer,it's better to use a BFH. BTW our plow tractor got fluid installed for plowin,removed the rest of the year to barrels.
Follow Ups:
Home
| Forums
Today's Featured Article -
The Day Mom Drove the 8N - by Brian Browning. My Dad was wanting to put in a garden but couldn't operate the 8N and handle the old horse drawn plow he had found and rigged up to use with the tractor. Well, he decided to go get Mom out of the house and have her drive the tractor while he walked behind the plow. You got to understand that while my Mom is a hard worker who will always help whenever she can... she had never operated farm machinery before that day. Dad got her out there, explained how the clutch was the same as in our o
... [Read Article]
Latest Ad:
Oliver 550 Diesel runs like a watch three point hitch pto engine gone threw about two hundred hours ago nice clean tractor
[More Ads]
Copyright © 1997-2024 Yesterday's Tractor Co. All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V. Yesterday's Tractors - Antique Tractor HeadquartersWebsite Accessibility Policy |
|