Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 
Marketplace
Classified Ads
Photo Ads
Tractor Parts
Salvage

Community
Discussion Forums
Project Journals
Your Stories
Events Calendar
Hauling Schedule

Galleries
Tractor Photos
Implement Photos
Vintage Photos
Help Identify
Parts & Pieces
Stuck & Troubled
Vintage Ads
Community Album
Photo Ad Archives

Research & Info
Articles
Tractor Registry
Tip of the Day
Safety Cartoons
Tractor Values
Serial Numbers
Tune-Up Guide
Paint Codes
List Prices
Production Nbrs
Tune-Up Specs
Torque Values
3-Point Specs
Glossary

Miscellaneous
Tractor Games
Just For Kids
Virtual Show
Museum Guide
Memorial Page
Feedback Form

Yesterday's Tractors Facebook Page

  
Tractor Talk Discussion Board

Re: value of old riding mower


[ Expand ] [ View Follow Ups ] [ Post Followup ] [ Return to Forum ]

Posted by rustyj14 on January 18, 2005 at 10:32:59 from (209.195.142.160):

In Reply to: value of old riding mower posted by aggieamy on January 14, 2005 at 13:24:54:

1. Check for spark! Hold end of spark plug wire metal part, have somebody pull the starter rope! you'll be able to tell right quick if it has spark! Or, clamp the spark plug to the engine, with the wire attached and plug out of cylinder head, pull rope sharply, watch end of plug-look for sparking. If spark, go to step 2. If no spark, will probably need points and condenser. Install new points/ condenser. Don't know how? Access Briggs or Tecumseh web sites, or buy a small engine handbook/ repairs, etc.
3. Detach carburetor, carefully dismantle, clean in laquer thinner, or buy a quart of carb cleaner. Soak in cleaner over night, being sure not to soak any rubber or cork gaskets, seals, etc. Next day, blow out all passages, clean fuel bowl, Watch you don't blow out any small seals, gaskets, etc. They fly thru the shop and hide someplace, leaving you to tear out yer hair, trying to find it/ them! (You'll find them next summer while searching for something not related to those parts.)
4: Install new sparkplug, set gap to .030! Clean out fuel tank with laquer thinner, allow to dry, re-install, and put in a quart of gas.
5: Drain out old oil, allowing it to drain well! Install new SAE 30 non-detergent oil. (Some think detergent oil is better, but those old engines will run great on the non stuff!) Add oil in the fill hole. If it has a slanted hole on the lower part of the block, add oil until it runs out, then put in plug!
6: with spark plug out, pull starter rope 5-6 times to distribute the new oil, then install spark plug and wire. Set choke, or move throttle control to "Start". Pull rope sharply, may take a bunch of pulls. If engine tries to start, move throttle handle off choke position to "run"!
If all else fails, go pick the brain of the nearest lawn mower guy, maybe he can help you!
7: If you can get it running, it will be worth a lot more than if it doesn't run. Somebody may be interested in it for nostalgia, but those folks are few! Might as well invest a few hours in it, to get more for it!
by: Rustyj


Follow Ups:




Post a Followup

:
: :

:

:

:

:

: If you check this box, email will be sent to you whenever someone replies to this message. Your email address must be entered above to receive notification. This notification will be cancelled automatically after 2 weeks.


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Today's Featured Article - The Nuts and Bolts of Fasteners - Part 2 - by Curtis Von Fange. In our previous article we discussed capscrews, bolts, and nuts along with their relative hardness and thread sizes. In this segment we will finish up on our fasteners and then work with ways to keep them from loosening up in the field. Capscrews, bolts and nuts are not the only means of holding two parts together. When dealing with thinner metals like sheet tin, a long bolt and ... [Read Article]

Latest Ad: Oliver 550 Diesel runs like a watch three point hitch pto engine gone threw about two hundred hours ago nice clean tractor [More Ads]

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy