Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 
Marketplace
Classified Ads
Photo Ads
Tractor Parts
Salvage

Community
Discussion Forums
Project Journals
Your Stories
Events Calendar
Hauling Schedule

Galleries
Tractor Photos
Implement Photos
Vintage Photos
Help Identify
Parts & Pieces
Stuck & Troubled
Vintage Ads
Community Album
Photo Ad Archives

Research & Info
Articles
Tractor Registry
Tip of the Day
Safety Cartoons
Tractor Values
Serial Numbers
Tune-Up Guide
Paint Codes
List Prices
Production Nbrs
Tune-Up Specs
Torque Values
3-Point Specs
Glossary

Miscellaneous
Tractor Games
Just For Kids
Virtual Show
Museum Guide
Memorial Page
Feedback Form

Yesterday's Tractors Facebook Page

  
Tractor Talk Discussion Board

Re: Best way to break in a rebiult motor


[ Expand ] [ View Follow Ups ] [ Post Followup ] [ Return to Forum ]

Posted by RN on November 27, 2004 at 18:41:22 from (166.126.218.219):

In Reply to: Best way to break in a rebiult motor posted by Bill from Seneca, IL on November 27, 2004 at 18:06:38:

Breakin rebuilt? Lots of ways, here is opinion for your Cub this time of year- 10W valvoline racing oil in engine, 1 cup 30w non detergent low ash oil to 5 gallons gas for start. 1st 2/5 hours running don't get over 2/3 throttle. vary speed up/down while under light load- wagon pulling or something like light cultivating garden. Next 5 hours can go to full trottle medium load. Garden plow/cultivate/mow in low gear short rows - vary engine speed end rows and turns. Drain oil at about 10 Hours, switch to 10w30 weight, change filter, reduce oil in gas to 1 cup to 10 gallons. Go next 25 hours up to near full throttle and medium loads while varying engine speed occasionaly- slow to idle on corners, end rows, whatever/whenever you feel like it. Drain oil at 20-25 hours and run 10w30 for winter, 15/40 or straight 30 for summer. Try to change oil at least twice a year or 100 hours afterwards, no more oil in gas needed. Rings should seat in 1st 5-10 hours, valves should work lap themselves to seats and guides and bearings fit themselves to journals at same 5-10 hours. Second 5 hours under some load should have engine at full operation temp. At 1st oil change 10 hours, check head bolt torque/retorque to specs, check intake/exhaust bolts also, check valve lash clearance. RN.


Follow Ups:




Post a Followup

:
: :

:

:

:

:

: If you check this box, email will be sent to you whenever someone replies to this message. Your email address must be entered above to receive notification. This notification will be cancelled automatically after 2 weeks.


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Today's Featured Article - Women and Tractors - More Views From the Farmer's Wife - by Teri Burkholder. The top ten reasons why the judges wouldn't let you participate in the stock antique tractor pull: Hey, this is stock! It came with that V8 in it! That "R" on my tires stands for "really old" not radial! Blue gas? We thought it was a pretty color! What wire hooked to my throttle? ... [Read Article]

Latest Ad: Sell 1958 Hi-Altitude Massey Fergerson tractor, original condition. three point hitch pto engine, Runs well, photos available upon request [More Ads]

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy