Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 
Marketplace
Classified Ads
Photo Ads
Tractor Parts
Salvage

Community
Discussion Forums
Project Journals
Your Stories
Events Calendar
Hauling Schedule

Galleries
Tractor Photos
Implement Photos
Vintage Photos
Help Identify
Parts & Pieces
Stuck & Troubled
Vintage Ads
Community Album
Photo Ad Archives

Research & Info
Articles
Tractor Registry
Tip of the Day
Safety Cartoons
Tractor Values
Serial Numbers
Tune-Up Guide
Paint Codes
List Prices
Production Nbrs
Tune-Up Specs
Torque Values
3-Point Specs
Glossary

Miscellaneous
Tractor Games
Just For Kids
Virtual Show
Museum Guide
Memorial Page
Feedback Form

Yesterday's Tractors Facebook Page

  
Tractor Talk Discussion Board

Re: follow up on 5th wheel hitch location


[ Expand ] [ View Follow Ups ] [ Post Followup ] [ Return to Forum ]

Posted by T_Bone on July 02, 2004 at 22:18:42 from (4.240.132.201):

In Reply to: follow up on 5th wheel hitch location posted by Duane on July 02, 2004 at 21:28:26:

Hi Duane,

From all the install manuals I've read, most state there's less than 1% front axle loading difference from 4" behind to 4" in front of the axle.

From a optimum pulling stand point, axle center line to forward of axle center line pulls best.

If you want to see in writing what the Dealer is told to install too, including drilling holes and where you can drill those holes, framing welding, etc; can be found on the Ford commerical truck website titled
"Ford Body Builders Handbook"

For 2005 Ford has changed several items on the F250 to F550 spec's. I just repeating what I've read on different websites and not from Ford other than when Ford was direct quoted;

Frames on the F250/F350 SWR has changed to a heavier frame to be rated at 23,500 GCWR, tops in the industry.

4wd drive axles on the F250/F350 SWR are now a coil frame attached attached by a strut to the frame, simular to Dodge, which was a night mare the first few years for Dodge (weak design)

F350/F450/F550 DRW will still use the leaf spring mounting on 4wd, much stronger design of Fords past.

Both Dodge and Ford Both look the same and if Ford took off the "blue Oval" in the center of the grill, it's close to a Dodge look.

That was the only differences I was looking at as I'm sure there's more.

You would need the builders handbook for your model year, not 2005 which may be why Ford has changed mounting deminsions.

I've seen the 2003 manaul and your good there before the axle as in previous years but I haven't looked at a 2004 manual.

T_Bone



Follow Ups:




Post a Followup

:
:

: Re: Re: follow up on 5th wheel hitch location

:

:

:

:

: If you check this box, email will be sent to you whenever someone replies to this message. Your email address must be entered above to receive notification. This notification will be cancelled automatically after 2 weeks.


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Today's Featured Article - History of the Nuffield Tractor - by Anthony West. The Nuffield tractor story started in early 1945. The British government still reeling from the effects of the war on the economy, approached the Nuffield organization to see if they would design and build an "ALL NEW" British built wheeled tractor, suitable for both British and world farming. ... [Read Article]

Latest Ad: Oliver 550 Diesel runs like a watch three point hitch pto engine gone threw about two hundred hours ago nice clean tractor [More Ads]

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy