Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 
Marketplace
Classified Ads
Photo Ads
Tractor Parts
Salvage

Community
Discussion Forums
Project Journals
Your Stories
Events Calendar
Hauling Schedule

Galleries
Tractor Photos
Implement Photos
Vintage Photos
Help Identify
Parts & Pieces
Stuck & Troubled
Vintage Ads
Community Album
Photo Ad Archives

Research & Info
Articles
Tractor Registry
Tip of the Day
Safety Cartoons
Tractor Values
Serial Numbers
Tune-Up Guide
Paint Codes
List Prices
Production Nbrs
Tune-Up Specs
Torque Values
3-Point Specs
Glossary

Miscellaneous
Tractor Games
Just For Kids
Virtual Show
Museum Guide
Memorial Page
Feedback Form

Yesterday's Tractors Facebook Page

  
Tractor Talk Discussion Board

Re: Re: Anyone ever added a turbo to a tractor?


[ Expand ] [ View Follow Ups ] [ Post Followup ] [ Return to Forum ]

Posted by RAB on March 06, 2004 at 05:48:51 from (195.93.34.11):

In Reply to: Re: Anyone ever added a turbo to a tractor? posted by kyhayman on March 05, 2004 at 20:07:30:

Mainly true. May need a bigger main jet as well or maybe the adjuster would let enough in (not forgetting the gas engines). Suppose it might depend on how much/little boost, and where in the work range.
Adding a turbo does effectively improve power output without extra fuel. A diesel runs really lean anyway, but increasing the effective compression pressure would provide more combustion air (possibility of cleaner combustion) and at a higher temperature due to theoretical adiabatic compression. The useful work done by any fuel is increased by increasing the temperature and pressure differences (before and at the end of the working stroke), so laws of thermodynamics indicate the engine should run more efficiently ie a LITTLE more power for the same fuel.
Even though the exhaust gas kinetic energy, converted in the turbo, is 'free' there are other things like extra lubrication, extra loads on bearings, extra cooling required, etc etc which make fitting a turbo ineffective cost-wise without other changes.
For instance you could turbo a 'sea level' tractor for high altitude work (no, not flying!), but it is so much easier/cheaper to raise the compression ratio by milling the head!
Just a few cranky thoughts to muddy the waters and perhaps demonstrate that all sorts of things are theoretically possible, but not necessarily sensibly practical!!
Regards, RAB


Follow Ups:




Post A Followup

:
:

: Re: Re: Re: Anyone ever added a turbo to a tractor?

:

:

:

:

: If you check this box, email will be sent to you whenever someone replies to this message. Your email address must be entered above to receive notification. This notification will be cancelled automatically after 2 weeks.


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Today's Featured Article - The Nuts and Bolts of Fasteners - Part 2 - by Curtis Von Fange. In our previous article we discussed capscrews, bolts, and nuts along with their relative hardness and thread sizes. In this segment we will finish up on our fasteners and then work with ways to keep them from loosening up in the field. Capscrews, bolts and nuts are not the only means of holding two parts together. When dealing with thinner metals like sheet tin, a long bolt and ... [Read Article]

Latest Ad: Oliver 550 Diesel runs like a watch three point hitch pto engine gone threw about two hundred hours ago nice clean tractor [More Ads]

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy