Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 
Marketplace
Classified Ads
Photo Ads
Tractor Parts
Salvage

Community
Discussion Forums
Project Journals
Your Stories
Events Calendar
Hauling Schedule

Galleries
Tractor Photos
Implement Photos
Vintage Photos
Help Identify
Parts & Pieces
Stuck & Troubled
Vintage Ads
Community Album
Photo Ad Archives

Research & Info
Articles
Tractor Registry
Tip of the Day
Safety Cartoons
Tractor Values
Serial Numbers
Tune-Up Guide
Paint Codes
List Prices
Production Nbrs
Tune-Up Specs
Torque Values
3-Point Specs
Glossary

Miscellaneous
Tractor Games
Just For Kids
Virtual Show
Museum Guide
Memorial Page
Feedback Form

Yesterday's Tractors Facebook Page

  
Tractor Talk Discussion Board

sand, etc


[ View Follow Ups ] [ Post Followup ] [ Return to Forum ]

Posted by andy on May 17, 2003 at 15:46:21 from (204.30.228.118):

Good evening gentlemen, and ladies,

Someone recently put a handful or so of play sand in my gas tank. I found it in the fuel filter, then I removed and cleaned the fuel filter, gas tank, and fuel line. Put it back together, put gas in it and it ran as well as it usually does. However, now, about 3 days later, I run it for a while until it gets good and hot, then it begins to backfire and die. The first time this happened I changed the oil, which it needed anyway, also cleaned the air intakes. The next day, today, it runs for a while until hot, then backfires and dies. It would restart and run for a short time, then die again, repeatedly. NOW it won't start. It started and ran the last time but at a VERY slow pace, then when it quit it wouldn't start again as I just said.

I cleaned the spark plugs, two of which were clotted with oily junk, two of which had light white deposits on them. I'll replace these as soon as possible. Also changed the air cleaner oil. Still no luck.

Background on this tractor: last summer I had the distributor weights replaced, cause it wouldn't run. then it would run, but has been underpowered since. The flywheel marks are worn away, but I moved the distributor back and forth so that it would pull at least some load, but right now it's like 18-20 hp instead of 50. That is, if it would start, right now. Should I lift the distributor out and rotate it before reinsertion? How do I do that? thank you so much in advance for any ideas.
Andy




Follow Ups:




Post A Followup

:
:

: Re: sand, etc

:

:

:

:

: If you check this box, email will be sent to you whenever someone replies to this message. Your email address must be entered above to receive notification. This notification will be cancelled automatically after 2 weeks.


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Today's Featured Article - The Nuts and Bolts of Fasteners - Part 2 - by Curtis Von Fange. In our previous article we discussed capscrews, bolts, and nuts along with their relative hardness and thread sizes. In this segment we will finish up on our fasteners and then work with ways to keep them from loosening up in the field. Capscrews, bolts and nuts are not the only means of holding two parts together. When dealing with thinner metals like sheet tin, a long bolt and ... [Read Article]

Latest Ad: Oliver 550 Diesel runs like a watch three point hitch pto engine gone threw about two hundred hours ago nice clean tractor [More Ads]

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy