Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 
Marketplace
Classified Ads
Photo Ads
Tractor Parts
Salvage

Community
Discussion Forums
Project Journals
Your Stories
Events Calendar
Hauling Schedule

Galleries
Tractor Photos
Implement Photos
Vintage Photos
Help Identify
Parts & Pieces
Stuck & Troubled
Vintage Ads
Community Album
Photo Ad Archives

Research & Info
Articles
Tractor Registry
Tip of the Day
Safety Cartoons
Tractor Values
Serial Numbers
Tune-Up Guide
Paint Codes
List Prices
Production Nbrs
Tune-Up Specs
Torque Values
3-Point Specs
Glossary

Miscellaneous
Tractor Games
Just For Kids
Virtual Show
Museum Guide
Memorial Page
Feedback Form

Yesterday's Tractors Facebook Page

  
Tractor Talk Discussion Board

Tractor Seat ID for Museum Ship


[ View Follow Ups ] [ Post Followup ] [ Return to Forum ]

Posted by Johnny on February 05, 2002 at 19:54:15 from (205.188.199.56):

As a volunteer with the SS American Victory (a 1945 "Victory" ship in Tampa, FL) I'm helping repair/restore the anti-aircraft guns. They had two tractor type seats, one on each side for the gun's operators. One seat, in poor condition, remains. I assume the seats would have been an off-the-shelf item from one of the tractor manuf. of the day but I don't know which one so I can't really start tracking down a couple of replacements until I can figure out what I should be looking for.

The basics: 12 1/2" long by 13" wide. Attaches to a 1" gooseneck with slot in the top. 4" raised rosette in the center of the seat. 1/4" holes (3 of them) about 3" aft of the rosette with 1 1/2 " spacing btwn. centers. 7 thumb-sized indentations are aft of the 3 holes and just before the back of the seat base. The base then raises about 1" then curls straight down. The entire ridge around the seat rolls straight down about 1" to 2" without any further lips or beads. The seat is of pressed steel and is very basic and plain looking.

Can anyone make a guess as to the source? How about a reference book that might have pictures I could compare ours with. The replacements won’t have to be exact but I would like to have them look somewhat like the originals.

If there is a tractor seat "historian" out there I could use some help. Thanks in advance.





Follow Ups:




Post A Followup

:
:

: Re: Tractor Seat ID for Museum Ship

:

:

:

:

: If you check this box, email will be sent to you whenever someone replies to this message. Your email address must be entered above to receive notification. This notification will be cancelled automatically after 2 weeks.


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Today's Featured Article - Engine Valves - Some Helpful Information - by Staff. Intake - On the intake stroke the piston moves doward, sucking in carburized fuel through the open intake valve. Exhaust valve is closed. Compression - With both the intake and exhaust valves closed, the pistons upward stroke compresses or squeezes the fuel into the combustion chamber. Firing - Ignited by the spark, the compressed fuel explodes and forces the piston downward on its power stroke. Intake and exhaust valves are closed. Exhaust valves and seats are exp ... [Read Article]

Latest Ad: Oliver 550 Diesel runs like a watch three point hitch pto engine gone threw about two hundred hours ago nice clean tractor [More Ads]

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy