Posted by MarkB_MI on December 01, 2021 at 03:50:30 from (174.211.33.101):
I was going to reply to Crazy's reply to Stan ('Fence boards'), but thought I'd start a new thread.
I've found finished board thickness to be very inconsistent over the years. We all know a 'one inch thick' finished board is really 3/4 inch thick. Presumably that's because back in the day, after you planed an eighth of an inch off either side of a roughsawn board you ended up with 3/4 inch, more or less. But I bought some 1x6 white cedar about twenty years ago that was actually 5/8 inch thick. Why? I have no idea, but these were clear boards and fairly expensive. I tried to buy some more a couple of years ago at the same lumberyard but they no longer carry the stuff.
Roughsawn lumber used to be 7/8 inch thick, which made sense: If you only plane one side of a roughsawn board, you'll only take off 1/8 inch. But I bought some roughsawn cedar the other day and it was 3/4 inch thick. Apparently lumber mills realized they were giving away an eighth of an inch of wood. The interesting thing is a 'roughsawn' board isn't really roughsawn anymore as there are NO SAW MARKS. Instead, it looks like they use some sort of machine that tears up the grain and gives the wood a weathered appearance. I was using some of these boards indoors, so I actually sanded the rough surface to get rid of the splinters. My assumption is the lumbermills are using saws these days that require almost no planing, so it's necessary to rough up the 'roughsawn' wood to get a rough appearance.
I did get a couple of boards that actually were roughsawn. Those were about 13/16 inch thick, a bit thinner than the old stuff. I assume they came from a different mill than 3/4 inch thick boards.
Upload one or more videos to your post. Photo and video filesizes should be less than 5MB. Formats allowed are gif, jpg, png, ogg, mp4, mov, and avi. Be sure to use filenames without spaces or special characters, and filetypes of 3 digits lower case.
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]
Today's Featured Article - The Day Mom Drove the 8N - by Brian Browning. My Dad was wanting to put in a garden but couldn't operate the 8N and handle the old horse drawn plow he had found and rigged up to use with the tractor. Well, he decided to go get Mom out of the house and have her drive the tractor while he walked behind the plow. You got to understand that while my Mom is a hard worker who will always help whenever she can... she had never operated farm machinery before that day. Dad got her out there, explained how the clutch was the same as in our o
... [Read Article]
Latest Ad:
Oliver 550 Diesel runs like a watch three point hitch pto engine gone threw about two hundred hours ago nice clean tractor
[More Ads]
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy
TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
