Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 
Marketplace
Classified Ads
Photo Ads
Tractor Parts
Salvage

Community
Discussion Forums
Project Journals
Your Stories
Events Calendar
Hauling Schedule

Galleries
Tractor Photos
Implement Photos
Vintage Photos
Help Identify
Parts & Pieces
Stuck & Troubled
Vintage Ads
Community Album
Photo Ad Archives

Research & Info
Articles
Tractor Registry
Tip of the Day
Safety Cartoons
Tractor Values
Serial Numbers
Tune-Up Guide
Paint Codes
List Prices
Production Nbrs
Tune-Up Specs
Torque Values
3-Point Specs
Glossary

Miscellaneous
Tractor Games
Just For Kids
Virtual Show
Museum Guide
Memorial Page
Feedback Form

Yesterday's Tractors Facebook Page

  
Tractor Talk Discussion Board

Re: Which Magneto for a D?


[ Expand ] [ View Replies ] [ Add a Reply ] [ Return to Forum ]

Posted by Leroy on August 01, 2019 at 07:03:39 from (96.45.243.241):

In Reply to: Re: Which Magneto for a D? posted by Joel Sanderson on July 31, 2019 at 19:44:06:

I am a dummy when it comes to things like that but I have been able to take a Delco distributor completely apart and clean and put back together working. A distributor has to have a switch with wire in from battery and out to distributor. Too many years to remember just how things are hooked up there. If a Wico distributor throw away and replace with a Delco. Wico could not be repaired 40 years ago. On a mag Deere never put a switch on them. Sepposed to stop them by shetting fuel off, chocking or like we did, idle as slow as possible, put in high gear and apply both brakes and partially engauge clutch. Could be if you knew what to do be hooked to a switch to stop and it would be a one wire grounded switch like the IH Farmall had. If you had to use a normal 2 wire switch one was hooked to mag and the other was to place on dash where switch was mounted. Allis used a shorting strip on the mag.. I don't know of anybody in last 40 years that actually new what to do to work on a mag. I go to the Portland, Indiana tractor show every year and they usually have one or two mag repair on site venders there. Might just might be one for either the spring or fall swap meets. But then if you depend on it and have to wait a year to find one of those places you are stuck. Most anybody can figure out a Delco distributor.


Replies:




Add a Reply!
You must be Logged In to Post


:
:
:

:

:

:

:

:

:

Advanced Posting Options

: If you check this box, email will be sent to you whenever someone replies to this message. Your email address must be entered above to receive notification. This notification will be cancelled automatically after 2 weeks.

No political comments, hate speech or bigotry of any kind will be tolerated. Violations will be removed and posting privileges may be permanently revoked without notice.



 
Advanced Posting Tools
  Select Gallery Photo  Attach Serial No List 
Return to Post 
Upload Photos/Videos
Upload one or more videos to your post. Photo and video filesizes should be less than 5MB. Formats allowed are gif, jpg, png, ogg, mp4, mov, and avi. Be sure to use filenames without spaces or special characters, and filetypes of 3 digits lower case.

TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Today's Featured Article - The Tractor Parade: Story of a Case SC - by Bernie DeLon. On a early fall morning back in 1994, I opened the newspaper and happened to spy an article about a local antique tractor club having their annual show that weekend. ... [Read Article]

Latest Ad: Sell 1958 Hi-Altitude Massey Fergerson tractor, original condition. three point hitch pto engine, Runs well, photos available upon request [More Ads]

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy