Posted by DR. EVIL on April 16, 2019 at 05:47:18 from (174.197.8.48):
In Reply to: Bought a dump truck posted by SVcummins on April 15, 2019 at 20:27:23:
GMC didn't change styling much if at all to determine model years on their trucks. I'll assume that truck is too new to still have a Big Block V-6, and that's too bad. If it has an in-line 6, I hope for your sake it's a 292, the 250 was also available. My guess with the 5+2 trans it may have a 327 if it's old enough, most likely a 350 truck engine, and slim chance it has a 366 big block truck engine.
From posts on other forums I hope it has the 350. So many 350's were built parts are still available. 366 parts just don't exist anymore.
Summer of 1982 I helped my buddy harvest potatoes, drove truck hauling in. Had a pair of '66 or '67 C65's, one with 292-6 and 5+2, other had 350 & 5+2, and a Ford 750 with 6V-53 Detroit diesel and 5+2. The 350 powered truck was fastest loaded on the road, and O-K to load, and burned the most gas in a day. The 292 powered truck was second fastest loaded, by far easiest to match speed with the tractor powered harvester. The Ford was just a noisey nasty truck to drive. No skipping gears when loaded, could run thru transmission in low side of axle then shift to high when in 5th. Could run 2-3 days on a tank of fuel.
Township road commissioner I worked for had a '67 and '74 C-65's, both 366 & 5+2's. '67 geared to run about 58 mph, the '74 geared to run about 67 mph. I was the only driver the second year I worked there, the '74 was brand new that year. Put a lot of miles on that truck. Couple years later the township bought a second dump truck, a C70 tandem with 427 & 5+2. Never even got to sit in that truck.
Upload one or more videos to your post. Photo and video filesizes should be less than 5MB. Formats allowed are gif, jpg, png, ogg, mp4, mov, and avi. Be sure to use filenames without spaces or special characters, and filetypes of 3 digits lower case.
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]
Today's Featured Article - Talk of the Town: The Saga of Grandpa's Tractor - by The following saga is from the Tractor Talk Discussion Forum. Someone. The saga starts with the following message: Hey guys I have a decision to make. I know what you all will probably suggest and it will probably agree with me way down inside, but here it is. I have a picture blown up and framed in my "tractor room" of a Farmall M. It was my Grandpa's tractor, of which whom I never got to meet. He froze to death getting this tractor out of the barn to pull a truck out of the ditch before I was born. Anyway my dad and aunt had to sell it at the auction,
... [Read Article]
Latest Ad:
Sell 1958 Hi-Altitude Massey Fergerson tractor, original condition. three point hitch pto engine, Runs well, photos available upon request
[More Ads]
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy
TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.