Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 
Marketplace
Classified Ads
Photo Ads
Tractor Parts
Salvage

Community
Discussion Forums
Project Journals
Your Stories
Events Calendar
Hauling Schedule

Galleries
Tractor Photos
Implement Photos
Vintage Photos
Help Identify
Parts & Pieces
Stuck & Troubled
Vintage Ads
Community Album
Photo Ad Archives

Research & Info
Articles
Tractor Registry
Tip of the Day
Safety Cartoons
Tractor Values
Serial Numbers
Tune-Up Guide
Paint Codes
List Prices
Production Nbrs
Tune-Up Specs
Torque Values
3-Point Specs
Glossary

Miscellaneous
Tractor Games
Just For Kids
Virtual Show
Museum Guide
Memorial Page
Feedback Form

Yesterday's Tractors Facebook Page

  
Tractor Talk Discussion Board

Re: Hydraulic Cylinders


[ Expand ] [ View Replies ] [ Add a Reply ] [ Return to Forum ]

Posted by Steve@Advance on March 02, 2019 at 15:03:35 from (66.169.147.211):

In Reply to: Hydraulic Cylinders posted by big_red_man on March 02, 2019 at 14:14:29:

Are you sure pressure is being applied to each side of the cylinder?

If the tractor valve is set up for a one way cylinder, it will only apply pressure to one hose, the other will only be a return to tank.

A true one way cylinder will almost always have a large rod, almost the same size as the bore. The rod seal will not be capable of holding pressure, it only serves as a dust seal.

If you are sure you are getting pressure to each end, and the cylinder is not responding, you will need to check the internal seals.

Disconnect and plug one hose, leave the cylinder port open. Block the cylinder mid way on the stroke, operate the valve to pressure up the attached line. Hold the valve and watch for oil to come out the open port. Once the slack is out and the cylinder is not moving, there should be very little, preferably no oil coming from the open port. You should also hear the engine load and see the line pressure against the blocked cylinder. That proves pressure is being delivered.

Reverse the procedure, remove and cap the attached line, attach the other. Same test, should give the same result.

If oil flows through the cylinder, the piston seals are bad. If the engine/pump do not load, there is no pressure being applied to that circuit.


Replies:




Add a Reply!
You must be Logged In to Post


:
:
:

:

:

:

:

:

:

Advanced Posting Options

: If you check this box, email will be sent to you whenever someone replies to this message. Your email address must be entered above to receive notification. This notification will be cancelled automatically after 2 weeks.

No political comments, hate speech or bigotry of any kind will be tolerated. Violations will be removed and posting privileges may be permanently revoked without notice.



 
Advanced Posting Tools
  Select Gallery Photo  Attach Serial No List 
Return to Post 
Upload Photos/Videos
Upload one or more videos to your post. Photo and video filesizes should be less than 5MB. Formats allowed are gif, jpg, png, ogg, mp4, mov, and avi. Be sure to use filenames without spaces or special characters, and filetypes of 3 digits lower case.

TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Today's Featured Article - The Tractor Parade: Story of a Case SC - by Bernie DeLon. On a early fall morning back in 1994, I opened the newspaper and happened to spy an article about a local antique tractor club having their annual show that weekend. ... [Read Article]

Latest Ad: Sell 1958 Hi-Altitude Massey Fergerson tractor, original condition. three point hitch pto engine, Runs well, photos available upon request [More Ads]

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy