Posted by bjb in Tx from Ne on July 24, 2018 at 13:10:18 from (147.1.235.122):
In Reply to: Re: My experiment... posted by showcrop on July 24, 2018 at 10:43:57:
The load needs to open the crack tip (in this case the leading edge) which gets developed in three ways.
1. Tension loading radially due to the spinning blades (no moment, but still a fatigue load). The stress range in this case is 0 to full stress at a particular location at the full speed of the blades. The number of stops and starts is your number of cycles. Note in this setup, tension is not constant; it is zero at the free edge (tips) and maximum near the bolt.
2. Varying load due to the blades hitting air (wind resistance); hitting grass; or in extreme cases hitting say a small tree. This will cause a bending moment on the blades, which also causes tension in the leading edge due to this moment (note that when the mower is loaded the speed changes the tension as mentioned in part 1 so the stress range due to this mowing "moment" is amplified). In theory, ever blade of grass creates a small stress range, but you also could look at the speed of the mower due to changes in resistance and create stress range and number of cycles that way as well.
3. Bending and tension caused by vibration due to the out of balanced blades. Here the number of cycles is directly related to the frequency of the vibration.
A few other points: The way fatigue design works is the previously mentioned S-N curves (Stress verses cycle) curves, plots the maximum number of cycles at any given stress range. Using the previous equation for damage, you can see how much life as a % is used at any stress range and then add the damage together to estimate the service life.
For most steels there is a minimum stress range to cause fatigue, however, with such large "cracks" in the serration and the expected hardening of the leading edge of the face, makes this a highly likely area for rapid fatigue damage.
There is a case of "low, cycle fatigue" where at extremely high stress ranges, the life goes from thousands of cycles, to tens of cycles. This would be the case if the mower were to be spinning fully and come to a dead stop by hitting a large unseen object. A few times will rapidly increase the crack growth.
Upload one or more videos to your post. Photo filesizes should be less than 300K and Videos, less than 2MB. Formats allowed are gif, jpg, png, ogg, mp4, mov, and avi. Be sure to use filenames without spaces or special characters, and filetypes of 3 digits lower case.
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]
Today's Featured Article - New Hitches For Your Old Tractor - by Chris Pratt. For this article, we are going to make the irrational and unlikely assumption that you purchased an older tractor that is in tip top shape and needs no immediate repairs other than an oil change and a good bath. To the newcomer planning to restore the machine, this means you have everything you need for the moment (something to sit in the shop and just look at for awhile while you read the books). To the newcomer that wants to get out and use the machine for field work, you may have already hit a major roadblock. That is the dreaded "proprietary hitch". With the exception of the
... [Read Article]
Latest Ad:
Sell 1958 Hi-Altitude Massey Fergerson tractor, original condition. three point hitch pto engine, Runs well, photos available upon request
[More Ads]
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy
TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
