Posted by Bruce from Can. on July 04, 2018 at 03:49:09 from (74.12.68.226):
Been baling hay since I was 13 , and I have never in the past 44 years had this happen. New Big round balers do a much better job of sweeping the field clean than balers of years gone by. And there is more clearness in the throat for the hay to pass pver the pickup as it enters the baler. It seems to have achieved this, the pickup is smaller, and the bars holding the pickup teeth turn faster and have very little clearance between the bars that hold the teeth and the stripper bands on the outside of the pickup. So if the baler drops into a hole , or hits some other object that is hidden from view by the windrow of hay causing the pickup to bottom out , the stripper bands will come into contact with the rotating bars holding the teeth. Last year we had too much rain, and I left some ruts in the field while haying, bales over this area, and baler dropped into some wheel tracks 4-6” deep at the end of the field, I didn’t think much about it. While later the pick up wasn’t working as it should. Bent a stripper band and ripped it right off !! Never seen anything like that happen before. So while I checked out the carnage under the pickup, I found two more bands bent a bit farther over from the broken band , bent another occasion . Both of these other bands had little more than a quarter inch of clearance before hitting the rotating bars. My baler has about 3000 bales through it now , and it is a Kubota. Went to my buddies place he has a year old NH , crawled under his pickup for a look, similar story. Many bands with small bends in them from bottoming out, and almost contacting the rotating bars holding the pickup teeth. So if you have a late model baler, crawl under the pickup and have a look now and then. New balers are not the rough rugged machines of days gone by. And you had better have billiard table smooth fields. Just a heads up .
Upload one or more videos to your post. Photo filesizes should be less than 300K and Videos, less than 2MB. Formats allowed are gif, jpg, png, ogg, mp4, mov, and avi. Be sure to use filenames without spaces or special characters, and filetypes of 3 digits lower case.
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]
Today's Featured Article - The Niagra View Mobile - Powered by a 1959 Ford Tractor - by Mark Massey. In 1959 the Niagara Frontier Transit Inc. of Buffalo, New York designed and built six Viewmobiles for the Niagara Frontier Sightseeing Inc. for use as a sightseeing ride at the Niagara Falls State Park, Niagara Falls, New York, powered by a 1959 Ford 611 Tractor.
... [Read Article]
Latest Ad:
Oliver 550 Diesel runs like a watch three point hitch pto engine gone threw about two hundred hours ago nice clean tractor
[More Ads]
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy
TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
