Posted by JDEM on March 02, 2018 at 12:23:18 from (174.230.9.47):
I have a 4WD Suzuki there that is driving me nuts. Actually -I have two in my shop with problems - but I will stick to one that has me most perplexed.
1995 4WD Suzuki King Quad 250 cc. Four-stroke-cycle engine. Ran fine when I pulled it into my shop last Fall. I did a lot of mechanical drive-line work and NO engine work. I made one change to the fuel system by changing the fuel-valve under the tank.
Now - it will not start. At this point - I refuse to believe the fuel-valve is the problem. But like I said - I am beginning to lose my mind on this thing.
Here is how the basic fuel system operates. Fuel valve that I changed has two positions. "Run" and "Primer." It has a vacuum-gas-shut-off-valve. So when in "Run" position - no gas can flow without engine vacuum. When in "Primer" position, that valve is bypassed and gas runs out freely. I tested the valve and it works. From there - the fuel delivery line goes to what Suzuki calls a "vacuum fuel pump." My factory service manual gives NO info on it other then " if it fails, replace it."
I guess I do not understand how this pump is supposed to work. I have worked on similar looking pumps on two-stroke-cycle engines that worked off of crankcase impulses. This is however a 4-stroke-cycle. The port on the intake manifold it hooks to provides a steady 6-7 inches of vacuum and no pulsing I can perceive.
I took the fuel-pump apart and all looks fine. Diaphragms are soft with no holes. Two check valves look fine. Put it back together and tested it with a hand-held vacuum-gun. A steady-vacuum and it pumps no fuel. A on-and-off pulsing vacuum and it still pumps no fuel. BUT - I then tried blowing air into it, off and on with pulses. This way it pumps lots of fuel.
So I am almost at the end of my rope. Seems I never had to think this hard before about a pump like this. I am very temped to put on an electric pump but it is hard to find one that really runs at low pressure. I have tested a few rated at 2-4 PSI and they ran higher. Likely too much for this carb.
I stuck a gravity feed tank on top of the engine and it starts and runs fine. The built-in tank sits near at carb level and needs a pump. So - I am getting a mental fog here. Suzuki does call it a "vacuum" pump and not an "impulse" pump. It hooks to the intake manifold and I cannot figure how there should be any impulse there anyway. Just a steady vacuum.
Somebody here got an idea about what I am missing here?
Upload one or more videos to your post. Photo filesizes should be less than 300K and Videos, less than 2MB. Formats allowed are gif, jpg, png, ogg, mp4, mov, and avi. Be sure to use filenames without spaces or special characters, and filetypes of 3 digits lower case.
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]
Today's Featured Article - Third Brush Generators - by Chris Pratt. While I love straightening sheet metal, cleaning, and painting old tractors, I use every excuse to avoid working on the on the electrics. I find the whole process sheer mystery. I have picked up and attempted to read every auto and farm electrics book with no improvement in the situation. They all seem to start with a chapter entitled "Theory of Electricity". After a few paragraphs I usually close the book and go back to banging out dents. A good friend and I were recently discussing our tractor electrical systems when he stated "I figure it all comes back to applying Ohms Law". At this point
... [Read Article]
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy
TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.