Posted by Janicholson on January 15, 2018 at 20:11:08 from (63.152.194.8):
In Reply to: Re: Farmall Super MD posted by vinnivee on January 15, 2018 at 18:58:37:
Lets try the following to see if it can be set right. Do not take it off of the engine. The oil can be drained from the pump from below (usually a petcock or plug) the side plate can be removed removing injector lines (from both ends) allows them to be taken out of the way (don't bend them out of the way). Removal of the big hex nut cover, and the fuel line fittings (where the lines were removed) will allow the top od the pump to be removed. This gains access to the internal components. You will see the plunger assembly on the right and a control rack that spins the sleeve to change the injection amount. the 4 holes to the left are a distributor system and usually give no problem. Use lacquer thinner on a small artists brush to wet the moving parts of the plunger and rack. keep it dampened with thinner and work the rack with the lever to apply pressure back and forth. DO not use force on the system, just enough to make it feel that it should move. Keep at it till things start to let go. Then use a thin oil like 3-N-1 to further lube the plunger control sleeve. WHen things seem free, you can put it back together. I have no sources for parts, I sold My MD 19 years ago, and fixed it 23 years ago. A Blue ribbon (IH) repair manual has all the details. I used a skim coat of permatex #2 for sealing up the top cover and side cover after making a gasket for the side cover. Take digital pictures of everything and be clean as can be. Fill it with engine oil to the site glass or level plug/petcock. 15W-40 diesel grade Rotella or Delo are my favorites. This is really all I have to offer and when it is written, it can be looked at more than once. Jim
Upload one or more videos to your post. Photo filesizes should be less than 300K and Videos, less than 2MB. Formats allowed are gif, jpg, png, ogg, mp4, mov, and avi. Be sure to use filenames without spaces or special characters, and filetypes of 3 digits lower case.
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]
Today's Featured Article - The Rescue of a Fordson F - by Anthony West. Introduction I live in the UK and have for many years restored Fordson tractors (in the main model N's). I have also restored and shown model F's, E 27N's, Field Marshall Series 2, David Brown Cropmasters and the old rey Fergeson T 20. At one time I had seven restored examples which were shown and used in ploughing matches. As most restorers, I have a number of war stories I can relate on a range of topics that may help other like minded and interested people. Perhaps my first p
... [Read Article]
Latest Ad:
Sell 1958 Hi-Altitude Massey Fergerson tractor, original condition. three point hitch pto engine, Runs well, photos available upon request
[More Ads]
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy
TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
