Posted by andy r on November 20, 2017 at 10:29:15 from (166.181.84.125):
In Reply to: 4420 stuck in the mud posted by cornguy77 on November 20, 2017 at 09:31:43:
I ran a Deere 4420 for several years. Honestly, I have never pulled one forward. Honestly, I never ever got the girl stuck. I have gotten hung up a few times with the corn head crossing a deeply shaped waterway where there may have been a cut occur over the growing season. Since the Deere 4420 doesn't really raise the head as high as some combines the skid plates under the head would catch on the other side of the shaped waterway. That would take weight off of the drive wheels and they would dig in trying to push the head forward. I would always hook under the rear "A" frame right in front of the rear axle and pull it backwards. It generally didn't take much to pull it off the high spot. I would not yank on the "A" frame. Make sure the chain is tight before you pull hard. I had a Deere 6620 rear wheel drop in a tile hole and the entire welded tube pulled out of the "A" frame. I think a key is if you are going forward and seem to be cutting in and getting stuck, STOP, and back out before you get stuck. I guess if it is that bad wait till it freezes some. Keep the hopper on the empty side. I really think that there is too much to damage by wrapping a chain around the front axle (brake lines/hydraulic hoses). Plus, would the chain clear the bottom of the header???? I remember over the years some guys flip - flopping the drive wheels (right on left/left on right) so the tread direction is reverse. That way if the combine can't go forward anymore you have a better chance of backing out of the wet area. Good luck.
Upload one or more videos to your post. Photo filesizes should be less than 300K and Videos, less than 2MB. Formats allowed are gif, jpg, png, ogg, mp4, mov, and avi. Be sure to use filenames without spaces or special characters, and filetypes of 3 digits lower case.
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]
Today's Featured Article - The 8N and the Fox - by Zane Sherman. Dec. 13 1998, Renfroe, Alabama. Last niht I dreamed about the day that I plowed the field of about 10 acres over on what Jimmy and Dandy called the Ledbetter field. I was driving the 1948 8N Ford tractor that Jimmy bought in 48 new This was prebably in about 1951 and maybe even befor the house was built. This would have made me to be about16 years old and I drove the tractor for nothing and would have paid to drive it if I had had any money which I didn't, but neit
... [Read Article]
Latest Ad:
Sell 1958 Hi-Altitude Massey Fergerson tractor, original condition. three point hitch pto engine, Runs well, photos available upon request
[More Ads]
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy
TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.