Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 
Marketplace
Classified Ads
Photo Ads
Tractor Parts
Salvage

Community
Discussion Forums
Project Journals
Your Stories
Events Calendar
Hauling Schedule

Galleries
Tractor Photos
Implement Photos
Vintage Photos
Help Identify
Parts & Pieces
Stuck & Troubled
Vintage Ads
Community Album
Photo Ad Archives

Research & Info
Articles
Tractor Registry
Tip of the Day
Safety Cartoons
Tractor Values
Serial Numbers
Tune-Up Guide
Paint Codes
List Prices
Production Nbrs
Tune-Up Specs
Torque Values
3-Point Specs
Glossary

Miscellaneous
Tractor Games
Just For Kids
Virtual Show
Museum Guide
Memorial Page
Feedback Form

Yesterday's Tractors Facebook Page

  
Tractor Talk Discussion Board

Re: Robert Shaw gas valve.


[ Expand ] [ View Replies ] [ Add a Reply ] [ Return to Forum ]

Posted by jeffcat on October 21, 2017 at 20:45:17 from (50.207.7.238):

In Reply to: Robert Shaw gas valve. posted by Fixerupper on October 21, 2017 at 12:51:33:

third party image

third party image

third party image

Hold on,,,, I went and looked at some of the Robert Shaw controls in our shop. What you bought is not like anything we have. First off that black knob with high low on it is adjusting the pressure diaphram that really should be set with a folded manometer to a certian water columb pressure. It makes it so the valve will allow a certian amount of gas in. Hi/lo flame. The two wires would need to be hooked together. Your thermal couple would supply the tiny amount of power to keep the valve open. Make and break ,on off, heat no heat deal, thermostat would hook to the black block. These valves are usually set up for milli volt and some are even micro volt. They also come in 24 volt AC supply and there are 120volt types. This is the trouble with fixing "home" appliances, and commercial equipment. Some of the ovens we have in the kitchens have 1 1/4" gas lines going to them. NOW. NOW!!!! Looking at your photo very carefully....that red cover, if you look inside of it there should be a threaded hole. That is where your thermal couple should screw in. At the bottom of that hole is a blue plastic block with some squished wire. Those two wires would go to a hi limit, and your thermostat would hook to the screws on the black block. Hope this is makeing sence. The valve in the first photo is for a Pitco fryer. Very common valve in our industry. Ours doesn't have that red cap but that is where the thermal couple screws in. For goodness sakes don't cross thread it! Also it is only a few foot inches of tightness. To me this is so simple but trying to explain it on a forum! Ufda. Let me put up the photos and if you have problems get back to me.


Replies:




Add a Reply!
You must be Logged In to Post


:
:
:

:

:

:

:

:

:

Advanced Posting Options

: If you check this box, email will be sent to you whenever someone replies to this message. Your email address must be entered above to receive notification. This notification will be cancelled automatically after 2 weeks.

No political comments, hate speech or bigotry of any kind will be tolerated. Violations will be removed and posting privileges may be permanently revoked without notice.



 
Advanced Posting Tools
  Upload Photo  Select Gallery Photo  Attach Serial No List 
Return to Post 
Upload Photos/Videos
Upload one or more videos to your post. Photo filesizes should be less than 300K and Videos, less than 2MB. Formats allowed are gif, jpg, png, ogg, mp4, mov, and avi. Be sure to use filenames without spaces or special characters, and filetypes of 3 digits lower case.

TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Today's Featured Article - The Niagra View Mobile - Powered by a 1959 Ford Tractor - by Mark Massey. In 1959 the Niagara Frontier Transit Inc. of Buffalo, New York designed and built six Viewmobiles for the Niagara Frontier Sightseeing Inc. for use as a sightseeing ride at the Niagara Falls State Park, Niagara Falls, New York, powered by a 1959 Ford 611 Tractor. ... [Read Article]

Latest Ad: Oliver 550 Diesel runs like a watch three point hitch pto engine gone threw about two hundred hours ago nice clean tractor [More Ads]

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy