Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 
Marketplace
Classified Ads
Photo Ads
Tractor Parts
Salvage

Community
Discussion Forums
Project Journals
Your Stories
Events Calendar
Hauling Schedule

Galleries
Tractor Photos
Implement Photos
Vintage Photos
Help Identify
Parts & Pieces
Stuck & Troubled
Vintage Ads
Community Album
Photo Ad Archives

Research & Info
Articles
Tractor Registry
Tip of the Day
Safety Cartoons
Tractor Values
Serial Numbers
Tune-Up Guide
Paint Codes
List Prices
Production Nbrs
Tune-Up Specs
Torque Values
3-Point Specs
Glossary

Miscellaneous
Tractor Games
Just For Kids
Virtual Show
Museum Guide
Memorial Page
Feedback Form

Yesterday's Tractors Facebook Page

  
Tractor Talk Discussion Board

JOhn Deere 2010 Diesel Timing- D/C or 26º retarded?


[ Expand ] [ View Replies ] [ Add a Reply ] [ Return to Forum ]

Posted by girroj2 on June 28, 2017 at 06:33:42 from (162.211.108.38):

I"m rebuilding a 1964/1965 (ish) John Deere 2010 Diesel. The tractor was recieved with the roosamaster injection pump (DBGVC429-2DH) loosely installed in the crank case, not timed. I had the pump rebuilt, they checked the correct timing marks, and also confirmed functionality on a calibration test stand. My John Deere manual specifies that timing needs to be set with the flywheel at TDC (D/C mark) but when the flywheel was at D/C; I did not have enough travel in the injection pump housing to align the timing marks on the pump. Assuming that someone had incorrectly installed the oil pump drive shaft a tooth off, I moved the oil pump gear one tooth, but still could not quite get the marks to align on the pump due to not enough travel on the injection pump housing. with the flywheel at D/C; it seemed that I was just a few degrees off where I needed to be. I called the pump rebuilder to confirm that he had checked the timing, and described my problem. He stated, that this pump was not designed to be timed off of D/C; but should be timed ~12 degrees retarded, he stated I should check the flywheel for a second retarded mark. I did, and found a 26º retarded mark, but according to my manual, this mark is for timing a gasoline engine! The funny thing is, using this -26º timing mark on the flywheel, the injection pump sits almost center on travel, and I could get the marks aligned on the pump. The engine starts up with a bit of turning over and seems to run pretty good (I think I need a new starter, seems to turn slower than needed, need to hook the new battery up to an additional 200amp charger to get it to fire up-but this is a separate issue). Has anyone ran into this timing issue on the late 2010 Diesel, and can confirm that I should be using the -26º retarded mark on the flywheel for this engine and pump combination?


Replies:




Add a Reply!
You must be Logged In to Post


:
:
:

:

:

:

:

:

:

Advanced Posting Options

: If you check this box, email will be sent to you whenever someone replies to this message. Your email address must be entered above to receive notification. This notification will be cancelled automatically after 2 weeks.

No political comments, hate speech or bigotry of any kind will be tolerated. Violations will be removed and posting privileges may be permanently revoked without notice.



 
Advanced Posting Tools
  Upload Photo  Select Gallery Photo  Attach Serial No List 
Return to Post 
Upload Photos/Videos
Upload one or more videos to your post. Photo filesizes should be less than 300K and Videos, less than 2MB. Formats allowed are gif, jpg, png, ogg, mp4, mov, and avi. Be sure to use filenames without spaces or special characters, and filetypes of 3 digits lower case.

TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Today's Featured Article - The Nuts and Bolts of Fasteners - Part 2 - by Curtis Von Fange. In our previous article we discussed capscrews, bolts, and nuts along with their relative hardness and thread sizes. In this segment we will finish up on our fasteners and then work with ways to keep them from loosening up in the field. Capscrews, bolts and nuts are not the only means of holding two parts together. When dealing with thinner metals like sheet tin, a long bolt and ... [Read Article]

Latest Ad: Oliver 550 Diesel runs like a watch three point hitch pto engine gone threw about two hundred hours ago nice clean tractor [More Ads]

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy