Posted by Craig2 on March 22, 2017 at 10:21:50 from (192.234.148.241):
I will try to make a long story short. About 4 years ago I bought a 47 2N Ford at auction. It looked good, had new tires, had been changed to 12 volt but the wiring was a birds nest. It wasn't stuck but didn't know if it ran. Ended up getting it for $400 and hauled it home. Started tinkering with it and found the gas tank was rusted BAD and sediment bowl was cracked. Opted for new gas tank, fuel shut off, and sediment bowl. Found all the bolts broken that hold the front wheels on and wheels were welded to the hubs. Found used wheels and hubs at a tractor show. I then got busy and the tractor sat in my garage for awhile. Finally got around to fixing the wiring and got a new coil, points and plug wires. Installed new tank, put some gas in it, hit the starter and eureka it runs. Drove it around the barnyard a bit. No smoke or engine noise so down the road I go. Drove it down to the crossroad and turned around. Half way back it died and wouldn't start again. Ok, figured the carb needs cleaned. Cleaned carb and installed a rebuild kit and it fired right up. Took it last fall to plow my parents garden and brought it back and put it in the garage. Fast forward to this week and I went to start it and got no spark. It's a front mount distributor so I removed distributor and coil and found the points to be out of adjustment. Adjusted points and pu'tt it back on the tractor and still no spark to the plugs. So here I go, take it off the tractor and adjust and clean and lube and put it back on still nothing. Off again and on again on, off, on, off, on #^%%&%&#%$#$^ I will wait til later. Last night I go out determined to get this thing going. First thing I have to clean off work bench from previous project. Start putting away tools and things back where they belong and there it is. The answer to all my problems. Laying on the bench was the rotor that is supposed to go under the distributor cap. Put it back on and it fired right up. Now you know why I don't post alot. It reveals too much about myself. ROFL Hope everyone got a good chuckle at my expense. LOL Craig
Upload one or more videos to your post. Photo filesizes should be less than 300K and Videos, less than 2MB. Formats allowed are gif, jpg, png, ogg, mp4, mov, and avi. Be sure to use filenames without spaces or special characters, and filetypes of 3 digits lower case.
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]
Today's Featured Article - The Nuts and Bolts of Fasteners - Part 2 - by Curtis Von Fange. In our previous article we discussed capscrews, bolts, and nuts along with their relative hardness and thread sizes. In this segment we will finish up on our fasteners and then work with ways to keep them from loosening up in the field. Capscrews, bolts and nuts are not the only means of holding two parts together. When dealing with thinner metals like sheet tin, a long bolt and
... [Read Article]
Latest Ad:
Oliver 550 Diesel runs like a watch three point hitch pto engine gone threw about two hundred hours ago nice clean tractor
[More Ads]
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy
TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
