Posted by 1206SWMO on March 18, 2017 at 06:01:39 from (99.198.1.196):
Yesterday I attended the Johnson sale just NE of Ft Scott,Kansas....It was cloudy to start with but turned in to a beautiful mostly sunny 72 degree day...Gene bought and sold tractors and implements for over 40 years and was a fixture at the area farm sales..He parted out some tractors too..Theres lots more than what the pictures show..
966 IH with Loader----$8,500--Run nice
756 IH diesel----$4,200--Run nice
Most of the tractors below didnt run but some would with just a little work..
1939 M Farmall #1265----$2,300----block had been patched-not running
520 JD-----$1,025
3414 IH diesel loader tractor-----$1,400-----ran
4010 JD gas------$1750
4010 JD LP-----$1700
620 JD----$1800
B JD with loader-----$600
B JD----$500
60 JD------$600
D-15 Allis----$1575----went to some AC friends in SE Kansas whom will have it running today
H Farmall------$550---nice rear tires
SC Case with mounted 2 row planter----$475 for scrap----a friend bought the planter for $100 to save it
400 IH diesel----$500
190 AC diesel for parts-----$575---engine free-friend got it
MM with loader-----$440
NH 660 baler-----$1450
M Farmall----$475
JD 2 bottom plow----$210---another one sold for $100
480 IH 21 ft disk-----$410----friend got it for parts
(2) New Holland rakes with hitch---$2300
Weights $10 to $65 each with the IH being the highest
400 IH planter-----$375----nice
AC 190 XT for parts with loader-----$1300---Another XT for parts-----$825
There were numerous IH parts tractors there with lots being M's---They sold for $175--225 per ton-- lots of scrap iron piles there that went for $200 a ton or better
Upload one or more videos to your post. Photo filesizes should be less than 300K and Videos, less than 2MB. Formats allowed are gif, jpg, png, ogg, mp4, mov, and avi. Be sure to use filenames without spaces or special characters, and filetypes of 3 digits lower case.
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]
Today's Featured Article - The Nuts and Bolts of Fasteners - Part 2 - by Curtis Von Fange. In our previous article we discussed capscrews, bolts, and nuts along with their relative hardness and thread sizes. In this segment we will finish up on our fasteners and then work with ways to keep them from loosening up in the field. Capscrews, bolts and nuts are not the only means of holding two parts together. When dealing with thinner metals like sheet tin, a long bolt and
... [Read Article]
Latest Ad:
Oliver 550 Diesel runs like a watch three point hitch pto engine gone threw about two hundred hours ago nice clean tractor
[More Ads]
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy
TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
