Posted by Ken Christopherson on March 15, 2017 at 14:39:44 from (63.231.157.111):
Hello all! Well, I am working on converting all of my tractors over to 12 volt with alternator. Farmall M, H, and John Deere A should be easy. My Case SC, however seems to prove a little more difficult as for as mounting goes. Here are my questions:
I picked up 2 Hitachi 14231 alternators as it is smaller and not as 'bulky' as the Delco 10SI (which I have two of, one for my M and one for my JD A). Plan to put the Hitachi on the Farmall H and Case SC. Delco 10SI will go on the JD A and Farmall M. Here are my options or plan of attack at mounting the alternator on the Case:
Option 1) Drill a 3/8 hole through the front flange of the engine block (See photo of screwdriver pointing to marked location, and mock-up placement of alternator). This would leave approximately 1/4" of material left above the hole. I would then mount the alternator using a 3/8" shoulder bolt with sleeve spacers to obtain the correct spacing. The top adjustment bracket would still be used in the factory location (although I would have to make a new one). My only concern is will I risk the front flange of the block cracking through this drilled hole? The tractor doesn't get heavy use - mostly just threshing shows and may get occasional yard chores at our next property.
Option 2) Remove the rear-most tab on the bottom side of the alternator (possibly compromising the strength of the front tab). Mount in the factory generator location. My concern here is the bottom front tab, if it is the only mounting point, will eventually crack or break due to both vibration and the amount of weight that is being held by just the single bottom tab.
Option 3) Mount the alternator in the factory generator location, but this would involve having someone fabricate a custom bottom bracket (as I do not have a welder). This is probably the most secure method, but would be quite involved. I don't have easy access to equipment to do this.
What are your thoughts on this? Would I be better to use a Delco 10SI? It seems that this alternator fits nicely, it is just the mounting that is giving me concerns. (I can always use the Hitachi on the Farmall M, and a Delco on my Case).
Upload one or more videos to your post. Photo filesizes should be less than 300K and Videos, less than 2MB. Formats allowed are gif, jpg, png, ogg, mp4, mov, and avi. Be sure to use filenames without spaces or special characters, and filetypes of 3 digits lower case.
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]
Today's Featured Article - Engine Valves - Some Helpful Information - by Staff. Intake - On the intake stroke the piston moves doward, sucking in carburized fuel through the open intake valve. Exhaust valve is closed. Compression - With both the intake and exhaust valves closed, the pistons upward stroke compresses or squeezes the fuel into the combustion chamber. Firing - Ignited by the spark, the compressed fuel explodes and forces the piston downward on its power stroke. Intake and exhaust valves are closed. Exhaust valves and seats are exp
... [Read Article]
Latest Ad:
Oliver 550 Diesel runs like a watch three point hitch pto engine gone threw about two hundred hours ago nice clean tractor
[More Ads]
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy
TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
