We're talking about horsepower here or watts if you will......1 hp = 746 watts (volts x amps in a dc circuit, considered to be the period of a second, unless time is involved, like hours for watt-hours or the more familiar term: kilowatt-hours for household power consumption).
To spin a certain engine at a certain speed under certain conditions for a certain length of time takes a certain amount of "work" measured as HP or kW x time required.
A battery stores "work" as "unconsumed" energy (which is the definition of work when consumed) in the form of watt-seconds meaning it will supply x number of volts x amps x time.
CCA makes no mention of the other two elements of energy storage: At how many volts, for how long. If we were to take the time to look up the definition of how the CCA rating is to be determined, we would see "the rest of the story" (Paul Harvey).
Starters in my corral require approx. 10v across the starter to spin up and when considering connectivity losses, which increase drastically when larger engines are involved due to higher amperage requirements, at least 11v needs to be at the battery terminals.
Sulphate is an oxide scale forming on the conducting plates of the battery as a result of the electric charge and the Sulphuric Acid-water (H2SO4+H20) solution. When it gets thick enough and enough vibration is present, some of it falls to the bottom of the battery case and in time piles up.
Sulphate amounts to a resistor in the circuit, inside the battery. Current flowing through the battery develops a counter voltage across this "resistance" which subtracts from the terminal voltage under the cranking load. Since the starting circuit is a "series" circuit, resistance anywhere in the circuit acts the same in limiting available current flow for a given voltage. Static battery voltage value does not take this into account as there is no current hence no counter voltage drop.
This is where the battery tester comes into play. It forces the battery to deliver whatever current you select and tells you the terminal voltage of the battery. (I have a HF unit and works great) If the battery is under charged or sulphate coated plates, the terminal voltage falls off fast as the current is increased. Using a reference from my Mercury 90 hp outboard motor service manual, the stated starting current is 120 amps. I use 12.75V year around as my benchmark value for a fully charged lead acid battery, rather than a Hydrometer which I don't have.....todays digital multimeters makes this possible.
If I need 10V at the terminals of the starter at 120 amperes for as many seconds as it takes for the engine to light off, then the total circuit resistance can't be greater than (12.75v-10v)/120 amps = 0.023 ohms which is hard for the connectivity to measure with suitable wire and the connections clean, and bright, and tight, much less any resistance in the battery. So yes, sulphate matters as does size (surface area) and number of plates.
One thing I found (conventional "old school" LA batteries) is that the lower the CCA for a given battery size (24, 27, whatever) the shorter are the plates. The shorter the plates, the more room at the bottom of the battery for sulphate to collect before it shorts out a cell.
I don't know what happens when you put a fiberglass mesh between the plates like some current battery technology. Seems to me it improves the life span and maybe that's why I just got 9+ years out of the battery that was in my 2007 Branson 6530c. I never got that much service out of a battery.
Well, I didn't have anything else to do this morning. It's a "cabin" day and "cabin fever" is quick to set in. Hope I remembered it all correctly. I do things like this to keep what mind I have left active.....I think. Grin
Upload one or more videos to your post. Photo filesizes should be less than 300K and Videos, less than 2MB. Formats allowed are gif, jpg, png, ogg, mp4, mov, and avi. Be sure to use filenames without spaces or special characters, and filetypes of 3 digits lower case.
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]
Today's Featured Article - Talk of the Town: The Saga of Grandpa's Tractor - by The following saga is from the Tractor Talk Discussion Forum. Someone. The saga starts with the following message: Hey guys I have a decision to make. I know what you all will probably suggest and it will probably agree with me way down inside, but here it is. I have a picture blown up and framed in my "tractor room" of a Farmall M. It was my Grandpa's tractor, of which whom I never got to meet. He froze to death getting this tractor out of the barn to pull a truck out of the ditch before I was born. Anyway my dad and aunt had to sell it at the auction,
... [Read Article]
Latest Ad:
Sell 1958 Hi-Altitude Massey Fergerson tractor, original condition. three point hitch pto engine, Runs well, photos available upon request
[More Ads]
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy
TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
