Posted by Steve@Advance on August 28, 2016 at 18:49:30 from (107.203.134.67):
In Reply to: 2n coil ck. posted by smokey37 on August 28, 2016 at 12:07:03:
What kind of problem are you having? No spark? Intermittent spark? Poor performance?
If the distributor is still on the engine, and there is no spark, you can test the continuity of the points and the primary winding of the coil with an ohm meter. Disconnect the wire from the ignition switch. Connect an ohm meter to the terminal on the distributor where the ignition wire was connected, the other lead to a bare metal ground. Turn the engine through and watch the ohm meter.
If the meter shows no reading, open circuit, then there is a problem with the points not connecting, or the primary winding of the coil is open, or there is a connection problem between the power terminal and the coil, or between the coil and the points.
If the meter reads 1 1/2 to 3 ohms resistance, no change when turning the engine through, the points are closed, or there is a short to ground between the coil and the points.
But if the ohm meter fluctuates between open circuit (points open) and 1 1/2 to 3 ohms (points closed), the circuitry in the coil/distributor is sufficient to make the coil fire.
Reconnect the ignition wire. Be sure there is voltage to the terminal with the ignition on. Check the voltage with the points closed. This puts the circuit under load. If it's still a 6 volt system, there should be close to battery voltage to the terminal. If it's been converted to 12 volts, and a resistor installed, should be around 6 volts.
If all this checks out, and there is still no spark, that narrows it down to the coil, the rotor or the cap. At this point, you'll need to remove the distributor assembly and do more diagnosis. Removing and installing the distributor is easy, and it will only go back on one way. It's the only way to be able to see what you are doing, to get everything set and routed correctly.
A bad condenser won't completely stop a coil from firing, unless it's shorted to ground. The ohm test above will reveal that. A bad condenser will cause poor running, or points arcing and burning. Best to just try another known good one.
Upload one or more videos to your post. Photo filesizes should be less than 300K and Videos, less than 2MB. Formats allowed are gif, jpg, png, ogg, mp4, mov, and avi. Be sure to use filenames without spaces or special characters, and filetypes of 3 digits lower case.
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]
Today's Featured Article - Talk of the Town: Repairin a Gas Tank - by Staff. This interesting discussion is from the Tool Talk Discussion Forum. Remember that safety is your first priority - make sure you know what you are doing before attempting a potentially dangerous activity!
... [Read Article]
Latest Ad:
Sell 1958 Hi-Altitude Massey Fergerson tractor, original condition. three point hitch pto engine, Runs well, photos available upon request
[More Ads]
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy
TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
