Posted by MarkB_MI on July 17, 2016 at 03:26:14 from (70.194.0.244):
In Reply to: Re: DOT?? posted by Geo-TH,In on July 16, 2016 at 18:10:48:
Good morning George!
1 slug = 32.174 pounds (mass) Acceleration of gravity on earth: 32.174 ft/s2
Coincidence? No. The mass unit of slug exists only so F=ma works out without using any conversion factors. Of course you just move the conversion out of the equation when you convert from pounds to slugs. In the real world nobody uses slugs. I don't buy a 644 slug sack of potatoes, I buy a 20 pound sack of potatoes. In the classroom, the slug is a useful unit of measure that clarifies the difference between weight and mass; in the real world it just gets in the way.
No, I don't have an MS in physics. My college physics was taught using only Systeme International (MKS) units, as were statics and dynamics. But the various thermodynamics courses I've taken used both SI and English units. Pounds-mass was always the unit of mass we used, NEVER slugs.
So, you ask, how do you get F=ma to work without using slugs as your unit of measure for mass? The engineer uses a conversion factor: one pound-force equals 32.174 pounds-mass feet/sec2. So to calculate the force required to accelerate 2000 pounds at 1 G:
F = ma = 2000 lbm x (1 lbf / (32.174 lbm-ft/s2)) x 32.174 ft/s2 = 2000 lbf
Notice that the pounds-mass units cancel out in this equation. As do the ft/s2 units. That's very important for the engineer; engineers always check unit consistency to confirm their calculations.
Upload one or more videos to your post. Photo filesizes should be less than 300K and Videos, less than 2MB. Formats allowed are gif, jpg, png, ogg, mp4, mov, and avi. Be sure to use filenames without spaces or special characters, and filetypes of 3 digits lower case.
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]
Today's Featured Article - The Engine Rebuild Kit - by Curtis Von Fange. I always liked engine rebuild kits. They have all the replacement parts for overhauling an engine without going to the store to get gaskets, special measuring tools, or miscellaneous parts. They come neatly packaged, clean and tidy. But it's important not to let that packaging lull you into a false sense of security. The appearance of matching sleeves, pistons, rings, and bearings can cause frustration and agony if not properly measured and installed in a workshop environment. Following c
... [Read Article]
Latest Ad:
Sell 1958 Hi-Altitude Massey Fergerson tractor, original condition. three point hitch pto engine, Runs well, photos available upon request
[More Ads]
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy
TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
