Posted by Adirondack case guy on December 20, 2015 at 09:54:13 from (74.69.160.79):
I like to build machines to make my firewood operation fun and easier. I built the skidding arch several years back. The blade is easily removed and my 3pt splitter locks onto the arch in it's mounting points. I built the ginpole on the splitter to pull logs out of the piles at the landings and the grapple to lift the heavy blocks. I built the elevator to eliminate dropping split wood back on the ground after splitting. I now just have to get the unsplit blocks on the splitter, and the elevator does the rest. I have acess to the big tandem trailer from the farm, and just finished a smaller hyd dump trailer of my own which will also fit into my walk-in celler where I store wood for the fireplace in the house. We burn that when ocasional heat is needed in early fall and spring when it starts warming up. The Royall boiler which is in my shop does all the major heating, house-celler-shop, during the winter heating season. I built the red cart to bring in wood to the boiler from the attached woodshed. In the celler I use a converted feed cart to wheel a batch of wood from pile to where the dumb waiter is. The dumb waiter is made from Kubota crates and overhead door rollers and track. I mounted a HF 120V winch up in the trusses to raise and lower the dumb waiter. The last pic is of a chopsaw tab le that I built years back to block slabs off my home built bandsaw. I need to fab some brackets so I can quick couple it to the splitter for transport. It will free stand once set up at landing and dump directly into the elevator hopper. I'm tierd of bending over and chaseing smaller limbs with the saw to cut them to length. I can't work like I used to, but my shop built machines provide the muscle that I no longer have. To those of you who ask why not just hook to natural gas, the answer is easy. There are no NG lines in the area. Besids I like building things. the Kubota crates and other materials that I build stuff from are free, and I love working in the woods. On top of that You can't beat wood heat. Loren, the Acg.
Upload one or more videos to your post. Photo filesizes should be less than 300K and Videos, less than 2MB. Formats allowed are gif, jpg, png, ogg, mp4, mov, and avi. Be sure to use filenames without spaces or special characters, and filetypes of 3 digits lower case.
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]
Today's Featured Article - The Nuts and Bolts of Fasteners - Part 2 - by Curtis Von Fange. In our previous article we discussed capscrews, bolts, and nuts along with their relative hardness and thread sizes. In this segment we will finish up on our fasteners and then work with ways to keep them from loosening up in the field. Capscrews, bolts and nuts are not the only means of holding two parts together. When dealing with thinner metals like sheet tin, a long bolt and
... [Read Article]
Latest Ad:
Oliver 550 Diesel runs like a watch three point hitch pto engine gone threw about two hundred hours ago nice clean tractor
[More Ads]
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy
TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
