Posted by Chris Jones on November 02, 2014 at 07:15:52 from (65.188.217.236):
Since writing I had someone come get the rest of the pipe. When he called he said he was going to build a rack for his truck like mine before he came over. I told him how I made mine. He sounded like he knew what he was doing. When he showed up I almost couldn't believe my eyes. He used 3/4" x 1.25" wood for uprights. One cross piece was 3/4 x 3.5 (1x4) and the other cross piece was much smaller and looked to have been split off something--not cut. A mismatch of bent over nails and screws held it together. After loading 1/2 the pipe it almost broke. I suggested cutting to 10 foot lengths but he didn't want to. He'd driven over an hour so another trip wasn't an option. I finally decided and convinced him that as he had an 8 foot bed he could put them in the bed and over the tailgate and let them stick way out. He had 3 straps. 2 he used to bundle the pipe into a circle. Next as his Dodge didn't have any tiedown IN the bed we needed to find a way to secure the pipe in bottom of the bed at the front. We snapped apart the "rack" and used the 1X4 cut to length to fit under his bedrails on both sides and slid back to hold the front of the bundle down but it was far from secure. The bed had a gooseneck receiver in the floor and I asked where he attached safety chains when using it but he didn't know anything about the hitch--came on the truck and he never used it. I finally felt ok for him to leave when I managed to pry some part of that gooseneck receiver up a bit (like a locking lever or something, it was 1/4" thick 2.5" wide). It had a hole in the end. The strap went into that hole around the pipe and to the middle stake pocket on the side and pulled tight. He then used bailing twine to tie the bundle at the back of the bed to the back stake pocket. I must have helped him for an hour. But now I felt it at least would not fall completely free of the truck in transit. Nice guy just didn't think things through.
I'm going to have to change my policies on helping folks load. Not sure what to do. I think I'll try a suggesting they bring 4 to 6 RATCHETING straps and tell them they are responsible for loading and tie-down themselves at the point I give people directions to my house. I'm wasting way too much of my time helping unprepared people load.
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]
Today's Featured Article - History of the Nuffield Tractor - by Anthony West. The Nuffield tractor story started in early 1945. The British government still reeling from the effects of the war on the economy, approached the Nuffield organization to see if they would design and build an "ALL NEW" British built wheeled tractor, suitable for both British and world farming.
... [Read Article]
Latest Ad:
Oliver 550 Diesel runs like a watch three point hitch pto engine gone threw about two hundred hours ago nice clean tractor
[More Ads]
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy
TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
