Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 
Marketplace
Classified Ads
Photo Ads
Tractor Parts
Salvage

Community
Discussion Forums
Project Journals
Your Stories
Events Calendar
Hauling Schedule

Galleries
Tractor Photos
Implement Photos
Vintage Photos
Help Identify
Parts & Pieces
Stuck & Troubled
Vintage Ads
Community Album
Photo Ad Archives

Research & Info
Articles
Tractor Registry
Tip of the Day
Safety Cartoons
Tractor Values
Serial Numbers
Tune-Up Guide
Paint Codes
List Prices
Production Nbrs
Tune-Up Specs
Torque Values
3-Point Specs
Glossary

Miscellaneous
Tractor Games
Just For Kids
Virtual Show
Museum Guide
Memorial Page
Feedback Form

Yesterday's Tractors Facebook Page

  
Tractor Talk Discussion Board

Re: 50 model fordson dextra


[ Expand ] [ View Replies ] [ Add a Reply ] [ Return to Forum ]

Posted by Steve@Advance on August 20, 2014 at 21:30:44 from (107.203.134.67):

In Reply to: 50 model fordson dextra posted by Ethan Mckeehan on August 20, 2014 at 19:51:56:

Something is up with the governor.

First, look at the linkage. The governor arm should be linked directly to the carb throttle lever.

Second, the lever on the dash, (the speed control lever) is connected to the governor arm with a spring. At idle, the spring is in the relaxed position. When the lever is pushed to the fast position, the spring is pulled tighter.

Inside the governor housing are a set of weights. The faster the engine runs, the faster the weights spin, the harder the arm pushes against the spring and wants to close the throttle.

So, the spring from the dash lever wants to pull the throttle open, the weights in the governor want to push it closed. With the engine running. there is a balancing act between the two forces that control the engine speed.

Start with the engine off, dash lever at idle. The throttle plate will be open or partially open, and can be pushed closed with minimal effort. The governor arm should travel freely the full range from throttle closed to wide open without binding or having excess slack or wear in any component.

Now move the dash lever to the fast position. The throttle should be spring loaded to the wide open position. You should be able to push it closed with moderate finger pressure, then it will spring back to full open when released.

If everything checks out, set the throttle at idle and start the engine. If it still over revs and the governor does not push the throttle closed, either something is wrong internally with the governor, or the linkage between the gov and carb is too short, running out of travel before the throttle is closed.

Once everything is adjusted and working properly the engine RPM should be 2000-2200.


Replies:




Add a Reply

:
:
:

:

:

:

:

:

:

Advanced Posting Options

: If you check this box, email will be sent to you whenever someone replies to this message. Your email address must be entered above to receive notification. This notification will be cancelled automatically after 2 weeks.



 
Advanced Posting Tools
  Upload Photo  Select Gallery Photo  Attach Serial # List 
Return to Post 

TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Today's Featured Article - The Tractor Parade: Story of a Case SC - by Bernie DeLon. On a early fall morning back in 1994, I opened the newspaper and happened to spy an article about a local antique tractor club having their annual show that weekend. ... [Read Article]

Latest Ad: Sell 1958 Hi-Altitude Massey Fergerson tractor, original condition. three point hitch pto engine, Runs well, photos available upon request [More Ads]

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy