I ran a BR740A for years and now have a BR7070. I have had great luck with them. The 740 is still going with about 12000 bales on it. Replaced one roller, belts, and we did have the pickup head off it a couple years ago and went through everything. That was kind of because of a traumatic injury tho. The 7070 has about 1000 bales through it and hasn"t missed a beat.
Check the obvious stuff. A lot of the zerks for the bearings are on grease banks, but there are about a dozen that aren"t. Figure out where they are and keep it greased and chains oiled. The chain in the pickup head does stretch and needs adjustment maybe twice a season.
If the 7060 is nearly new it should have the seamless belts on it, so no need to worry about the crimps on the belting. I guess if one tears you just replace that one with a crimp style, I haven"t had to yet. In my opinion, John Deere has a better crimp system, so any belts we replace on the 740 have come from Deere.
All the BR series balers make great bales, I love the big extra sweep pickup head and how it sits in front of the baler where I can see whats going on, its just what I am used to.
We have the crop cutter on both balers, use it some. It works great for tall or coarse grass hay. The other benefit I notice is with that rotor in the throat of the baler, they start a bale really easily, basically dump a bale and go. My FIL has a BR750 without the crop cutter and to start a bale with his, you do have to start a little slower and let the bale get rolling before you gear back up and go.
The BR series balers are great in dry/mostly dry hay. I think the big Vermeer balers are probably better if you get into a lot of wet hay to bag or big coarse slough hay. I have a couple of friends who run them, and I swear you could run a small horse through their pickup head and not slow down. In most other conditions, I will take my BR, but that"s just me.
Oh, but I do like how you load the net wrap from the back on the Vermeers. It is a slight pain on the BR"s to load it from the front. Mostly because you have to play ring around the baler and go from one side to unlock the roll, to the other side to pull the empty roll off, behind the baler to get the new roll, back to the side to put it on , then around to the other side to lock it in and start the roll. A pretty minor inconvenience, but frustrating when you always run out with one round left and rain clouds coming.. Hope any of this helps BW
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]
Today's Featured Article - The 8N and the Fox - by Zane Sherman. Dec. 13 1998, Renfroe, Alabama. Last niht I dreamed about the day that I plowed the field of about 10 acres over on what Jimmy and Dandy called the Ledbetter field. I was driving the 1948 8N Ford tractor that Jimmy bought in 48 new This was prebably in about 1951 and maybe even befor the house was built. This would have made me to be about16 years old and I drove the tractor for nothing and would have paid to drive it if I had had any money which I didn't, but neit
... [Read Article]
Latest Ad:
Sell 1958 Hi-Altitude Massey Fergerson tractor, original condition. three point hitch pto engine, Runs well, photos available upon request
[More Ads]
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy
TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
